Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello, Lesson 8, exercise 3, regarding bootloaders and BLE DFU, of the intermediate DevAcademy course had a compilation issue with the nrf5340 DK, and using TF-M. It was caused...
hello,
I tried to apply modifications to use and test the qspi flash mx25r6435f on the nrf9160dk development board. NCS version 2.2.0. I can not see her.
prj
overlay...
Hi,
we are developing a solution where the number of peripheral BLE devices is increasing and we need to manage up to 30 realiable connections. We have been working with...
Hi everyone,
I'm trying to send updated gyro and acceleration values from MPU6050 continuously by BLE function from nrf52832. I'm currently using the nrf52 development kit...
I would like to inquire whether there is a sample or guide to search for and connect to iPhone background advertising when operating with nRF52840/5340 Central.
https...
Hi
Followup on this ticket: Enabling SPI and TWI drivers on Zephyr
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
nRF...
Hi
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
I am trying to create a demonstration project, where I need both SPI and...
I am having trouble understanding how to measure the power consumption of the nRF9161DK as recommended by the documentation: https://docs.nordicsemi.com/bundle/ug_nrf9161_dk...
I'm working on a complex legacy codebase for the nRF52840, which uses nRF5 SDK 15.0.0 and the S140 SoftDevice v6.0.0. The device previously only used a custom RF protocol...
Hi,
I'm using SDK 2.1.0 for this project.
I found that when I shut down using the following:
pm_state_force ( 0u , &( struct pm_state_info){PM_STATE_SOFT_OFF, 0 ,...
I was trying to set up partitions on a nRF5340 DK so I can use MCUBoot, settings, and littlefs but am getting this error when flashing the dk:
The output Zephyr.dts has...
Dear Support,
I encounted an issue when tried to connect with complicated wifi network recently.
The error info is as follwing.
"WPA: 4-Way Handshake failed - pre-shared...
Hi,
we use our code for beacons for very long time now. Unfortunately producer changed chip.
We were using NRF51802QF with SoftDeviceS130.
Now the chip is NRF52810QCAA...
I am receiving the following errors: [00:00:00.117,187] <wrn> bt_hci_core: opcode 0x2027 status 0x12 [00:00:00.118,133] <err> bt_id: Failed to add IRK to controller Which...
