Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi.
I'm trying to add a SPM partition to my project. Like another project i did in the past, i followed this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
We would like to know there is any direct test mode for TX power of NRF21540DK.
We only found the method of nRF52833 direct test(TX). But we can find how to do with NRF21540DK...
Hi,
I wonder how to use the internal capacitor of the nrf5340.
The nRF5340-DK operates at 32M=8pf 32.768k=9pf without any special settings.
If i use 10pf products for...
Hi,
I'm porting firmware between nRF52 and nRF53 platforms. What is the equivalent of NRF_UICR-> CUSTOMER on nRF53 to keep data like serial number etc.
Thanks
Sebas...
We are developing a custom device based on the nRF9160 SiP Revision 2 with multiple connections over LTE-M and we are experiencing problems with keeping our only TCP connection...
Hello, I'm using nrf mesh serial example in nrf5sdkformeshv500src, in the serial node i subscripted to 0xC000 but i can't not received messages more than 32 node, my netwwork...
Hi All,
Sorry to ask this question, I just learned a little about cmake.
Now I wanted to add a few src files based on the light switch example in SES. Do I have to create...
Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hi.
I am trying to update my Softdevice using DFU.
If I update from S112 to S140, do I have to upload the application as an image built with S140 as well?
And do I need...
Hi there,
I can't seem to add header files to my project.
The header files underlined in red are not from the Nordic SDK installed from the Toolchain Manager.
...
Hello,
we are currently developing an MQTT Bridge Application. We plan to use a nrf52840 in combination with the nrf9160 as our Bridge which is going to send its data...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
I have developed my thread application based on nrf_sdk_for_thread_and_zigbee and implemented DFU OTA in my application. It is working fine with no issues.
I am using nrf52840...
Hi,
My nrf52840 is not detecting the USB, i tried by pressing the SW5 after that bootloader led starts blinking but not showing any drive in the PC also
can you please...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
