Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
The datasheet tells me that the default source of the low frequency clock (LFCLK) is the 32.768 kHz RC oscillator (LFRC). so I took the crystal oscillator off my PCB, but...
After updating NRF Connect v3.9.0 to eliminate the recently documented JSON + connectivity errors with nrf Programmer and Power Profiler, my bash scripts utilizing nrfprog...
Hi，
1. Please provide me with an example of BMA280
2. The SDK: replication v1.7.1
3.IC:nRF9160
4. I tried to change the BME280 driver to BMA280 driver, but the following...
I am working on project in which i want to read data from sd card and send it to mobile through BLE , I am using ble_nus_send to send data but when i decrease the delay then...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
Hi All,
Likely because I am still quite new to this, but I have started with MQTT simple example and whenever I do use GuiConfig to make mods, it saves them to
proj/build...
The disccussion here
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52-nrf51-dk-kit-doesn-t-work
has been closed.
I followed step 4 and it took a few tries...
Hi,
I use a Segger JLink EDU (the big version, not the mini) to flash some custom boards. This used to work fine until I upgraded nRF Connect and got Programmer v2.0.
...
Dear sir/madame,
By an accident I selected Power Profiler Kit II when I wanted to download an application to “PCA10056 DK” . After that ‘download’ Power Profiler Kit II...
Hello,
I'm using NRF52832 as a controller for cellular modem and used the AWS IOT supplied with the NRF Connect SDK.
I want to use the AWS FOTA and I'm a bit lost, I added...
This builds on a previous Forum Post that was closed out.
There is a peculiar issue with the NRF52840 SAADC sampling. For an unknown reason, triggering the SAMPLE Task in...
I have a nRF5340 with a UART that connects to a circuit that is not powered on until it is needed by the application. So the UART must be powered off until the application...
Hi,
We are developing cycling trainer, so we use BLE fitness machine profile. Our functions are basically completed and we are testing with some VR cycling windows or desktop...
Hello, please help if you can.
Once connected. I am asked to program the board when trying to use BLE from nerf connect.
However, I get the error: Error while setting...
