Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I'm trying to integrate buttonless dfu to our project. We don't have any security concerns and given the existing project constraints, it's not desirable to use peer_manager...
Hello,
I tried the smp_svr example with the nRF52-DK of sdk 1.6.1., i compile the solution whit segger v5.50c
I connect with the NRFConnect Device Manager app,
I try...
Hi all,
I am trying to get started with the Nordic thingy 91 but I am not able to update the latest firmware.
The programmer is only showing one Serial port. The instructions...
Hi Nordic Team,
I have interfaced bme280 with nrf52840 and I got the temperature successfully. I have used https://github.com/knuta/nrf5-bme280-twi link for that.
Here...
hi.
I use nrf52840 sdk nRF5_SDK_17.0.2_d674dde.
I need to control the H and L changes of IO within 300ns, I want to turn on the high-frequency part when necessary, and...
Hi nRF team,
we are building our project on top ble_template_example, and we want data encryption for bluetooth data .
we have seen below ways :-
1.) AES Encryption...
I had a generic USB dongle that I used to receive beacons on my machine from an nRF52832 chip.
To be able to perform OTA DFU, I replaced that generic USB dongle with an...
Dear NORDIC Engineers
I have a qustions about NRF52.We have a project that used NRF52833.We want to add the AOA&AOD function to the project.So I would like to know about...
Building the pc-ble-driver on an Arch Linux machine fails with the following error
./pc-ble-driver/src/pc-ble-driver-4.1.4/src/common/transport/uart_transport.cpp: In member...
Hi,
I'm considering using NRF52832/52840 as BLE central while configuring its I2C as slave.
Should I initialize I2C with TWIS instance? How do I suppose to set the slave...
Hello,
I am using the SMS sample of the NRF9160 SDK version 1.6.1. It allows to automatically send a SMS to a precise phone number, and to receive SMS.
As indicated at...
Hi,
I have been trying to use CMSIS DSP library over nRF52840. I added appropriate CONFIGs in prj.conf file, and cmake file. However, whenever I try to use function from...
Hi,
I would like to change the CDC_ACM UART (CDC_ACM_0) baud rate in runtime mode on nRF5340, but it seems to be not working. Below is my code snippet:
The return value...
Hello,
I am working on project where my requirement is something like... Device will advertise and it gets scanned by its own scanning.
What I have done so far......
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). At that time, an error occurs that "__ICFEDIT_region_RAM_start__" is not defined...
