Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello. I work on the multirole mode application. There is a strange situation, the conn_handle is not equal to 0 when connecting for the first time (equal to 2). Because of...
Hi. I am using nRF52840 DK as an central device to connect 6 peripheral device. There is no problem. But I want to add peripheral role to central device fo send data which...
Hi Nordic team/Everybody, I'm working with nRF52840 PCA10056 , Thread_Zigbee_ v4.1.0 , and light_control example.
I modifed, try to add T emp_measurement ZCL in Light_Bulb...
Hello, just updated from previous segger version to 5.34 but compiling an existing project
/ncs/v1.5.1/toolchain/segger_embedded_studio/lib/SEGGER_crtinit_v8m_mainline_little...
Hi
I am using the this example code nrf52-ble-app-uart-c-multilink [ https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink ]
If NRF_SDH_BLE_CENTRAL_LINK_COUNT...
Hi,
Would like to understand when will be the chip select pin be asserted and de-asserted when reading/writing a QSPI external flash?
What will enabling QSPI by setting...
Hello and to whom it may concern
I am currently using nRF51422_QFN48
with laser marking on the IC body
N51422QFAAF01616CS
i am using nRF desktop connect and try to...
Hello,
I'm having this problem with this nRF24L01+ connected to an ESP8266 (ESP12-E on BOB), and I'm using NodeMCU 2.2.1. The nRF24L01+ module I'm using is a small board...
Hello everyone,
i have a problem reading data from MAX30101 sensor FIFO. I set up the sensor and enable all 3 LEDS (Red, IR, Green), but when I read the data from the FIFO...
I'm using nRF Connect v1.5.0, Zephyr, and Segger Embedded Studio (SES) to develop an application I'm testing on nRF5340-DK.
I have a project that compiles and runs. But...
Due to the recent semiconductor global shortage, we are changing the chip on our device currently on the market from the nRF52832 chip to the newer nRF52833. I am in charge...
RNG interrupt handler is not called.
Using nrfx_rng library to generate random numbers.
VALRDY event is generated but interrupt handler nrfx_rng_irq_handler in library...
I have looked at the UART example provided in the NRF52 SDK. The example uses the UART in blocking mode. I need to create a version that is non-blocking, and only reads the...
Hello Nordic,
I was looking at multiprotocol support from nRF Connect SDK by following this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support...
Hi
Trying to install and operate the Sniffer based on nRF52840 USB Dongle
Having the nRF Connect for Desktop installed and burned the Dongle in accordance with the instructions...
