Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I have modified the asset tracking application to work with my AWS IOT account, I have noticed that after several minutes, the broker stops responding (not getting PUBACK...
Hi,
I am experimenting with ENC28J60 and PCA10056. Following are my connections:
================= =================================== NRF52840 PCA10056 ENC28J60 (pin...
Hi
I tried to implement Eddystone example in nRF52810. it worked successfully. Then i tried to implement same in nRF52832 using pca10040. But it not working. I only changed...
Hi, I'm running the saddc_pca10056 peripheral example given in SDK v15.2.0.
The analogue pin A0 is connected to the signal line of an LM35 temperature sensor. When I measure...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
I am porting RTC example code as is into ble_app_blinky...
hi...
i want to advertise the multi link central example , i have added the advertising in code , now my central is advertising but when i tried to connect , i am getting...
I programmed a NRF52840 Dongle with the example light switch code having changed the channel to 14 which is what my coordinator is on.
I then programmed a NRF52840DK with...
Good day,
I program my nRF52-DK with BLE Eddystone example's pre-compiled hex:
\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_eddystone\hex\ble_app_eddystone_pca10040_s132...
my bootloader.hex is generated by "nRF5_SDK_14.2.0_17b948a\examples\dfu\bootloader_secure_ble\pca10040\arm5_no_packs", my app.hex is generated by a modified blinky example...
I am currently using nRF8001 in my board (configured to connect - send data - disconnect - sleep every 30s cycle time). However, I am measuring about 140uA in average and...
Hello there.
I'm developing a custom board for the nrf52810 chip. I'm taking the reference files as a base for my own design, but I'm a little bit confused on which files...
Hi,
I am using nRF52840, SDK 15.0, softdevice 6.0.0 (toolchain IAR 7 on windows).
My application runs on FreeRTOS 9.0.0 tickless (NRF_SDH_DISPATCH_MODEL 2).
I have a...
Hi,
I want to get Battery ADC Value.
So. I simply used nrf_drv_saadc_sample_convert() function.
At first I thought it was the right value,
Later, I found that the...
