Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
We have worked with building a raspberry pi system that uses a nRf52832 dev kit board and the pc-ble-driver-js code to scan and connect to our bluetooth devices. This...
Add whitelist function in \ nrf5_sdk_15.2.0 _9412b96\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay, and report error 12804 (0x3204) after disconnection...
I'm trying to use the SAADC to return one value so I initialize it, try to take the reading, then unitize it so I can use it for taking readings through the PPI. The SAADC...
By default, is it enabling or disabling bias correction? If no, how to enable bias correction?
Is the RNG peripheral being left on all the time as a result of us using it...
hello,
I need send 10000bytes large data send central to peripheral in single transmission. I using example code ble_app_uart_c in SDK15.2 nrf52832. what are the parameter...
Hello
I am writing low-power application where NRF is called from the other chip by interrupt, performs bluetooth scan and sends data back over UART. Of course, I want to...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
I am using ‘ble_app_bliky” for my application development. In this “Button...
Hello =)
Im trying to run the ble_app_uart_c example on a NRF 52810 Chip.
i got:
SEGGER Embedded Studio for ARM V4.12
SDK 15.3.0
examples\ble_central\ble_app_uart_c...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
In ‘System OFF’ after GPIO interrupt, chip will reset and control will come...
Hi All
I am using nRF52832 with softdevice s132_nrf52.6.1.0
and I have to use both protocol (ble & gzll)
the default protocol is ble
after i keep pressing the button...
Hello,
I am working with nrf51822. I have developed a custom evaluation board. Accidently I connected voltage in reverse polarity to the device now i am unable to program...
Hi,
I am trying to understand possibilities provıded by Bluetooth Mesh Technology.
In my topology, there are tywo types node.
The first type of node is connected to...
Hii,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 2.0.1.
However, when I try to increase...
Hi. I'm using a nRF52840 chip and have a flavour of Proximity profile example being used with some custom services and characteristics that have been added. All is good in...
