Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
While visiting the Nordic Tech Tour we were discussing the pros and cons of BLE Mesh with a Nordic employee. He recommended that we also looked at a different solution, a...
This is essentially a repeat of :
https://devzone.nordicsemi.com/f/nordic-q-a/38808/is-a-3-bit-synchronous-3-data-lines-clock-parallel-input-at-16-368-mhz-feasible
Instead...
Hi,
I am using Keiluvision 5 , nRF5-SDK version - 15.2 with SoftDevice S140, My application requires to have NFC functionality as well as UART, but when I try to merge the...
Hi. need help with dynamic routing. I have a 9 node mesh running Thread and so far i have collected and analyzed latency data and packet delivery ratio data. I need to find...
Hello there,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hi Nordic,
I plan to use the newest SDK (because the ATT MTU > 23 is need) for NRF52832 to develop a PC tool to connect with Nordic BLE peripheral devices, and then send...
Hi, i am using SDK15.0.0 with nrf52840 chip.
I am interfacing a SPI device in the SPIM0. The SPIM module looks working fine without a softdevice.
But when i integrate...
SDK - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Hi,
I am using an android phone to write a 32 byte array to the nrf52 device which...
nRF51_SDK_10.0.0\examples\ant\ant_plus\ant_bsc\bsc_tx\combined\button\pca10028
ANT BSC Speed event time not change After a period of work although button press or relea...
Hi. I am a beginner with nrf52832. Trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
I have problem with both custom boards and DEV board.
From a certain time after GPIO direction bit seems not effecting the pins.
To get rid of software factor, I all erase...
Hello,
I'm currently using nrf8001 to sent a 20-byte packet. It works fine and my phone application receives the right data. However, when I send another packet that has...
Hi,
I try to create program which will save same data on SD card, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it...
nRF52832 custom board plus some devices. Using SDK 15
I want to count pulses from a previously configured accelerometer. Pulses are slow, around 500 per minute.
I have...
I am experienced with ARM Cortex-M devices, but new to Nordic. I am using C++, and have a publisher-subcriber event driven framework of my own in place already. My own software...
