Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello
I have implemented the stereo function to the nrf5340 audio application on SDK V2.6.0. i can send stereo audio signal to both of the two headset at the same time or...
Hi, I recently got nRF5340 Audio DK for my work. I have been try to use the onboard mic for collecting audio and transmit it via BLE, since I'm a newbie I couldn't do it....
Hi
I have successfully added the nrf_crypto files to the UART project. It compiles without any issue. Now I was trying to run the ECDSA example code in the UART project...
I used nrf52840 board with SDK 17_1_0
I used segger embedded studio IDE
i want to Implement two VL53L5CX TOF sensor with nrf52840 so i used two TWI,
but when i init...
Hello,
I'm migrating my project from using child/parent to sysbuild ( simple Hello world code, and using MCUBOOT + NSIB ).
The first error i faced when moving to use sysbuild...
Using Zephyr.
I'm looking for a process or a function to log unconditional message in the logging system including timestamp and other typical logging/display functionality...
We have a custom board with an nRF9160 directly connected to a SIM-S-IO3-MFF2-2 IC. I understand these kinds of eSIMs in IOT devices are typically provisioned over-the-air...
I have a slightly off the wall requirement where I need to send a serial data stream at 5kbps, it will be used to drive an external OOK 433MHz transmitter. The data format...
Hi,
I am having some issues when trying to enable the Fast Pair when executing the bt_fast_pair_enable(). I used the debugger to determine where it's failing:
...
Hello,
I am working on setting up the nrf52 (nrf52832) to communicated with the AD4130 from Analog Devices via the SPI Port. However, I am encountering a problem that I...
Hi,
I'm using the nrf9160, sdk 2.4.0 and tool chain 2.6.1. I need to scan the i2c sensor, I didn't find the i2c scanner example. So i was add one code and tested i'm getting...
I am trying to test the light switch and light bulb example with google home app and google nest device as a border router. I have flashed the bulb example into a nrf52840dk...
Hello, I've been trying to connect to cellular from our custom board (using nrf9160_ns) for the past few days. It already worked with the evaluation board using the same sim...
Hello,
I'm using the audio application provided by nRF. I want my device to play an audio file containing a sound saying "Connected" whenever the board is connected to the...
Hello, I'm running the nRF5 SDK's ATT_MTU throughput example and I want to check that the data sent by the 'tester' (nRF52832 in my case) is effectively received by the 'responder...
