I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
I am using a nRF5340 with mcuboot and multiple customer-specific partitions. I did not finish creating a separate board definition yet. Currently, we are using the...
Hi,
I am working on a project that uses nRF9160 SICA B1 and nRF52833 MCUs and currently we are researching possible Cloud providers that would ease the integration of FOTA...
Hello Community!
I have a question about connecting an external memory to the NRF52840. I noticed that it is not possible to connect an external RAM memory, but the QSPI...
I am trying to interface a PDM microphone to a NRF52840 using NRF Connect SDK v2.9.0. Does anyone have a good idea of how to get the DMIC sample to work on the NRF52840? The...
I am trying to use an ESP8266 ( ESP-01) to add Wifi capabilities to a nRF9160 project board. I am using nRF Connect SDK V2.9.0 and the V2.9.0 Toolchain.
To set it up I followed...
I have an NRF52840 DK (3.0.2) board, but it is not working. The USB port is not detected. When I power it through USB, the debug LED (LED5) turns on and then off. On the SoC...
Hi，
SDK:ncs2.6.1. The main program runs in the app core, and the net core is included as a child image. The Bluetooth broadcast is normal when tested at room temperature...
Hello Team,
I am trying to measure the sleep current of NRF54L15 DK, in the system ON mode, for that I am using Blinky sample code, from SDK version 2.9, which uses the...
Hello,
i recently received several nRF54L15DK kits.
The example good for channel sounding works well but left us with a question about the BLE antenna.
According to...
Hello when I build an application on VS Code, the terminal give this error :
warning: UPDATEABLE_IMAGE_NUMBER (defined at C:/ncs/v2.8.0/nrf\samples\common\mcumgr_bt_ota_dfu...
Do we have documentation anywhere detailing which pin is used or not in the 9161 DK and 7002 DK? I see docs like this:
Board control
Buttons and LEDs
I selected pin...
Hello ,
i m using sdk 15.0.0 and spi example for flash winbond 25q64 read write .
i m successfully read manufacture id,,device id.
but problem is writing and reading...
I'd like to know if the below info. is correct.
QDID of the nRF5340 chip itself : 11524
QDID of the Host system used in nRF Connect SDK version 2.8.0: Q322804
BR...
