Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
We have a design using a nrf5340 with a Renesas Wifi chip, That Renesas chip uses a 1 wire interface for Coexistence
We are using Zephyr 3.5.0 and have tried to follow https...
Hi, I have Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H for getting sound and for driving output via speaker I have tas2x63EVM amplifier. Since the nrf5340 audio dk...
Hi,
We want to have some RF-PHY tests on nRF52840 DK.
Therefore, I need a HEX file to make nRF52840 DK get into direct test mode and communicate with CMW270 with UART...
Hi,
I am currently testing the HID Keyboard example in SDK17.1.0. When the nRF52832 is connected to the computer and the Caps Lock key is toggled, it prompts "CAPS ON" or...
I tried to install nRF Sniffer. I followed the instructions here: https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-ble-sniffer/guides/installing_nrf_sniffer.html I...
SDK: NCS v2.6.0
Program Software: v2.6.0\nrf\samples\openthread\cli
Hardware：nrf52840dk_nrf52840 and third-party module(nrf52840 soc)
The program runs normally on...
I am writing to seek assistance regarding an issue I am encountering with the SPI0 interface in the NRF52840 module. The project requires the use of four SPI interfaces, but...
while trying to package my hex file from zephyr and I have gotten the following error
nrfutil pkg generate --hw-version 52 --sd-req=0x00 \
--application build/zephyr/zephyr...
I've been playing around with the MQTT example for the nrf7002dk and noticed that the mqtt_helper_publish function used from the MQTT Helper libraries doesn't handle acknowledgements...
Can someone please, for the love of all that is holy, point me towards some guidance on how to read values of custom characteristics set by another device?
I cannot find...
Hi,
My fw running on nRF52840 (ncs2.4.0, zephyr) develops from HRS sample application. It acts as a peripheral.
In this project, I have a dedicated thread to receiving...
Hi, this should be a straightforward question, I am writing some code to randomly generate a number, and it works fine the only issue is I don't know how to limit the range...
Hi , I try to use the BMI323 sensor . Its working fine for SENSOR _TRIG _DELTA interrupt . I want to use sensor fifo mode for BMI323 sensor , It seems not implemented fifo...
Hardware: nrf7002_nrf5340 Version: ncs-v2.61 Firmware: sample/aws_iot + BLE Mesh initialization ( chat_cli sample example ) Scenario:
My project requires BLE Mesh and MQTT...
Now I am using the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_central/README.html and https://developer.nordicsemi...
