Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello everyone,
I have developed a program that utilizes UART communication, Bluetooth Mesh, and TWI/I²C functionalities, all within the framework of the Zephyr project...
HI,
I am building an IoT product using NRF58233 ICs. In which I use 3 PWM channels and 3 ADC channels. You can review the principle I attached to make sure nothing went...
Hi,
I have a strange problem. I use a serial port timer to retrieve serial port data. When I compile with debug, the program runs normally, but when I compile with release...
Hi,
I am using nRF52840 DK and Bluetooth Observer example program. I am implementing filtering. I am having trouble add include scan.h which is located at C:\ncs\v2.4.2...
Hi Support Team,
I have an nRF7002 DK board and I am using SDK v2.6.0. I am facing an issue when sending data from the client to the server. Below are the steps taken: 1...
Dear colleagues,
with the newer SDK (I am now using NCS v2.5.0 and 2.6.0), I have difficulties finding the right SYSTEM OFF mode current. Code currently looks like as follows...
Hi
I use nRF7002 with SDK v2.52, try to connect external MCU and use uart call back function, to recieved and send bcak the recieved data, It will happen fatal error and...
Hi,
I have bunch of SEDs (sensors/clients) and one or more FTDs (hosts) working on CoAP protocol. SEDs send data packets once in a while and mostly sleeping. I have few...
Hi,
I'm testing the NCS direction-finding-connectionless demo,
NCS V2.6.0
this is my overlay:
and my ant_patterns:
According to the white paper and some other...
Please, I want to flash Zigbee Weather station App on thingy53, I faced two problems:
1- i can't find the board in build configuration.
2- i tried to use programmer and...
Team Nordic,
Question for you. In nRF5340 datasheet, page 1, Flash and RAM description : https://infocenter.nordicsemi.com/pdf/nRF5340_PS_v1.3.pdf
I found description...
Hi,
I am developping a non blocking TWI (I2C) communication, calling this function:
The init function of the twi is :
Please note that the real code is splitted...
I am having some issues with spurs when looking at the RF signal with a spectrum analyzer. The problem disappears when using __WFE() at the same time as sending constant carrier...
Hi,
is there a way to implement resume download, when downloading big files over HTTP(s).
Often during download of the bin file the connection is lost and we need to start...
I have used ncs-example application workspace to develop our project. In that we were trying to include WIFI, so we include all (sample/wifi/sta) content to my project. but...
