Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
hi support team,
1. customer asks about one question about hash in our dfu init packet.
our dfu lib will send init packet to our 52 device, how to use this hash in init...
I am creating a farm using nRF5340 Audio.
I am building and debugging using VSCODE, but suddenly the debugging behavior has become strange.
The symptom is that when step...
I'm having trouble figuring what hex update to flash to my card. I downloaded and unzipped the nrf9160dk_fw_2024-03-13_af2b60d2 file. I opened up the "Programmer" in nRF connect...
Hi Everyone,
I'm currently working on a project where I want to connect a input pin with a hardware counter using PPI. It used to work but I moved from a older nrf connect...
Hello,
While I was handling GPIO interrupts using Zephyr GPIO Driver in an sample that already uses the DK Buttons and LEDs driver, I get that the interrupt callback is...
Hello,
I work on custom device with custom FW, SDK16 S132 7.0.1 and NRF52832.
I have a custom service that have some custom characteristics.
my configuration:
CHAR...
Hello I am using the ST25R3911B on a board with the nrf5340 and the customer is asking for both reader and tag support. Would it be possible to use the same antenna for both...
According
sdk-nrf/subsys/nrf_security/Kconfig.tls - config MBEDTLS_SSL_DTLS_CONNECTION_ID
"The Connection ID extension is still in draft state."
Since March 2022 it...
I believe that the Nordic fork of hostap ( https://github.com/nrfconnect/sdk-hostap ) has a bug in os.h:
typedef uint64_t os_time_t;
The upstream has that defined as long...
I know how to set the TX power on an individual bluetooth handle basis per connection/advertisement. This is fine for advertising because I can create the advertising set...
In Bluetooth, in the example of multiple advertising sets, within the advertising parameters, there are minimum advertising intervals and maximum advertising intervals. Is...
Hi,
I try to communicate with a MRAM (MR25H128A) to nrf52832 board via SPI communication. I write an overlay file setting up all the necessary pins. Although I am getting...
If I'm building an iOS app to connect to a nRF5340 device and want to build DFU/FOTA into my app. I used the IOS-nRF-Connect app and followed the FOTA over Bluetooth Low Energy...
Hi,
i've been working on a ble central that's supposed to read tempeture value from a ble peripheral that i made ( i can read that value and see it being updated from the...
