Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I built a custom board with the nrf5340 and a SD card connected to non-standard gpios. My SD card is connected via SPI over the P0.14, P0.15, P0.16, P0.17, respectively for...
The latest toolchain has removed "serverArgs": from debug configuration in nrfConnect 2025.4.106
Is is mandatory as we only have RTT on our FF board and no serial...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
Hello,
Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance.
I would like to request any certificates...
Hi,
I'm working with the nRF54L15 SoC and running into an issue when using UARTE21 together with SMP over Bluetooth . Here's what I’ve observed:
UARTE21 works perfectly...
Hi,
I have an issue with nRF Kconfig GUI in VS Code.
My prj.conf is empty, and the _defconfig file of my board contains this:
When I open the GUI and...
I'm trying to get the USB Mass Storage sample working on the nRF52840 using SDK 2.9. I followed the official guide here: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hi!
I have somehow softbricked my nrf54L15 dk. This happened by using nrf conncet board configurator. First symptom was no uart logs and now I get this crash via RTT logging...
This issue is a follow-up to the previous one： 341132
When upgrading our device from Matter 1.1 to Matter 1.3 firmware via OTA, the MCUBoot program in the old firmware fails...
Hello,
I am conducting a feasibility study on implementing Auracast capabilities using the nRF5340 Audio DK with nRF Connect SDK v2.9.0. My goal is to investigate the potential...
Hi,
Recently, when I tried to obtain Bluetooth certification with nRF52840.
I found that there is a new requirement as shown below
RF:P1 - TRM/CA/03 Power Control
...
Hello,
I'm creating a simple test project based on the l4_e2 example, but I'm having trouble debugging it. The program encounters a fatal error before the main() function...
PPK2 is stuck in bootloader after trying to flash the latest firmware on Power Profiler 4.2.1 (Windows 10).
The error is "serialport could not be opened ". The same issue...
