Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello !
1. I have found in internet bootloader for dongle graviton_bootloader_mbr_v1.0.1-\[nRF5_SDK_15.0.1-1.alpha_f76d012\].hex and able to flash and use it.
But where...
Hi am trying to do bare metal programming using nRF52840 dk. I am working on UART protocol where I am trying to read a text file.
My text file look like this: It has 10...
I am using openOCD for flashing hex files to an nrf51 target. I have got the flashing process working.
However, I seem to be running out of space, the nrf51 has 256kB flash...
I'm trying to integrate MCUboot into my application, as immutable bootloader (CONFIG_BOOTLOADER_MCUBOOT=y). Building succeeded, but after programming the board gets stuck...
Hi,
I am using nrf52840, NCS v2.1.2.
I add MCUboot in my project, but got ‘Failed reading sectors; BOOT_MAX_IMG_SECTORS=256 - too small?’.
I add some log in MCUboot...
Hi,
I have been using the nRF5 SDK for years and the reason why I chose Nordic was for the low power consumption. Then when I was designing a new product using the nRF52840...
Board: nRF5340dk
SDK version: v2.1.0
My goal is to transmit 240 bytes of data every 5 ms using GATT notifications and 1 Mb PHY.
In the attached sample, I have my dev...
I added two extra buttons to ble_app_blinky (SDK 17.1.0) - port 1.10 and 0.31 I am running the code on an nRF52840 Dongle. The additional buttons are configured exactly like...
Hi,
I am using the sensor server example available in nrf5 sdk for mesh to build my own application on top of it. And the SOC we are using is nRF52832. I am trying to erase...
I see in the nrfx_uarte.c file the statement NRFX_LOG_INFO("Transfer about to send : %d bytes", length);
How can I set the logging for this file on?
#define NRFX_LOG_MODULE...
Hi,
My apologies if this is the wrong place for this.
I've been using the Power Profiler with the PPK2 and I'm very happy with the product, just have a couple small suggestions...
Hi there! I am facing " <err> download_client: Unexpected HTTP response: 400 bad request" error whenever I am trying to download full modem update from AWS S3 bucket. My environment...
Hi,
I attend the introduction course for the nRF's, and I am at Lession 3. The task is to print 'Hello World' to the device, using Serial Port and COMx. I have made the...
Hello,
As per the requirement of my project I need to add a header file into one of the thingy:53 sample.
Can you please guide how can I add a new header file into it...
