Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I am trying to interface nrf52840 with HMC5883L magnetometer sensor to read magnetic field x, y, z values.
When it comes to results, as far as i understood, values...
Hi,
I try to use nrf52840 dongle and pc-ble-driver-py to connect nrf5340 and get the data from it. The handle and uuid is obtained from nRF Connect for Desktop BLE and the...
Hello,
I am attempting to use the NRF twi manager based on the "twi master using nrf twi manager" example. I noticed that the example only reads and wrties a single byte...
I am having an issue with the BLE App Blinky example where I am receiving this error while trying to build using make on VSCode:
../../../../../../components/libraries...
Hello,
I created a sucessfull code for nRF5340-DK working with bluetooth, uart etc. I am using the Bluetooth NRF52 dongle
to test. When I upload the firmware to nRF-DK...
Dear community, I have multiple device chips I often re-use in multiple projects. So I wish to create a shared zephyr external library for re-use. What is the best way to...
Hi:
Example path:
C:\ncs\v2.1.1\zephyr\samples\subsys\nvs
Build Config:
nvs v2.1.1
" *** Booting Zephyr OS build v3.1.99-ncs1 *** "logs will not appear when running...
Hi
we are using nRF connect SDK 2.1.0 and also MCU boot.
Following the steps to generated the keys for signing the images.
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi.
i am using 5340 + ncs 2.0.2. and gpiote nrfx drvier.
i used gpiote for count encoder
encoder clock speed is about 2.5k and input pint is 2 gpiote pin.
gpiote polarity...
Hello there, I am having problems publishing a message to the server I set up on emqx. Here are the changes I made to the kconfig file (I have not changed the main.c code...
nRF52832にてボタンレスDFUサンプルにEEPROMを実装させたいのですが、
必要なライブラリファイルnrf_cli.cやnrf_queue.cをプロジェクトに追加したところ、 nrf_cli.ｈやnrf_queue.hが「no such file or directory」となり、
ビルドが失敗します。
components...
I've been using the LPUART for comms between the 52840 and 9160 in a Thingy91; this was going well until I changed the nRF Connect version from 1.9.1 to 2.1.2, to resolve...
When I call nrf_pwr_mgmt_run() in my project to put the device into sleep mode, after a short period of time I get the error message:
ERROR 3735928559 [Unknown error code...
Hello all
I am having a problem with nRF Connect SDK where whenever I try to read from a sensor while bluetooth is enables, the software crashes. If I disable bluetooth...
