My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi,
I was using JLink v7.50a with nrfjprog 10.9.0 and debug were working fine on Ubuntu 20.10 using SWD pins and JLink RTT. After changing to Ubuntu 21.10 and installing...
Hi Nordic team
We work on a custom hardware (LE Audio headset) and we need to send the battery voltage of the headset to the gateway which will be a smartphone. Using nRF...
Hi,
When SW9 is set to the default 1V8 position both the programmer and virtual COMs work fine.
When I switch SW9 to the 3V position the board is no longer detected...
Hi nrf team! I have been trying to get a couple of nrf5340 audio dk's to work with the "nrf5340_audio"-example, starting fresh with a clean install of VS Code even, and installed...
Hello
In my code i have two services one is blood pressure and second one is temperature and i have used button and indication both to send blood pressure data and temperature...
We have come to understand that the nRF5340 will not support BT classic (multiple tickets confirming this). But we still have a use-case that requires both BLE Audio and BT...
Hi guys,
I'm writing firmware for the nRF52840 using Zephyr, based on the cdc_acm example, using zephyr,cdc-acm-uart. I'm trying to blast out a ton of data, and need to...
hi devzone.
I have commercial product(led light receiver) which has nRF52832 chip and is running as central mode.
I install 'nRF connect for mobile' in my android phone...
I could not find a way, where I can get the nrfx_rtc_t const *p_instance for the nrfx_rtc_init function. There is no example where it is shown where to get this struct from...
Sometimes I get random JLinkARM DLL unknown error when I reset my device. I tried different PC, debugger, supply of chip. Nothing fixed this issue.
NRF52840 REV 3
nrfjprog...
Hi Nordic
Please explain the use of signals VDD_nRF_SENSE and VSENSE_SW_OUT in the circuit.
The board version I bought is PCA10095/0.11.0/2020.50.
Thank you.
Hi,
I just noticed that setting any of the CONFIG_BT_CTLR_TX_PWR has no effect on the range and RSSI while advertising. Does this config actually do something? I tested...
hello,
I have a DHT11 temperature and humidity sensor connected to Raspberry Pi 4 B. I want to transmit this data from this raspberry pi to another node using 802.15.4....
