Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I’d like to implement firmware updates where a central device (SMP Client) updates a peripheral (SMP Server) over Bluetooth.
I came across this repository: github...
I’m currently exploring peripheral support on the nRF54L15 and nRF54LM20A series controllers. I need to turn an LED on and off using the PWM component. The LED is connected...
We are developing a device based on the nRF5340 with an nPM1300 PMIC. The device has three power modes :
Active mode: most peripherals are enabled, and BLE communication...
I want to send Advertising packet with non-connectable and non-scannable via 2.4G without using the Bluetooth protocol stack. I try Congfig Nrf52832 's RADIO ,but it didn...
Hello
I am looking to use [as much as possible of] the full-speed USB bandwidth of 12 Mbps (or 1.5 MBps).
I have been able to use the USB MSC for my initial testing (with...
Hi All,
VS Code version 1.105.0
Mac Silicon, latest OS version installed : Tahoe 26.0.1
Since yesterday, my "nRF connect for VS Code" extension is stalled : the...
Hello, I came across the Location Services page for nRF Cloud and noticed that it supports multiple location technologies, which is quite promising. One line that stood out...
I recently started tooling with Zephyr for low power Bluetooth applications and i was trying to build with sysbuild mcuboot togheter with my nRF52832 without success. I see...
Hi,
I see that Nordic’s nRF Connect SDK now supports the Google Find Hub (Find My Device) SDK.
My question is would it be possible to build an asset tracking solution...
When we were configuring SDA in the visualized device tree, we forgot which button for SDA we should click (as shown in the red box in my picture). Now all the buttons for...
Using the matter weather station as a base on a thingy53 and SDK 3.1.0 which should use matter 1.4.2 if i open zap-gui and try and add a Control Bridge (0x0840) i get notification...
Hi,
1.Please troubleshoot the issue and identify the cause for no response when sending AT%HWVERSION using the merged_serial_lte_modem_v3.0.0.hex and mfw-pti_nrf91x1_2.3...
Hi,
I am currently working with Trusted Firmware-M (TF-M) on an nRF device and trying to understand the design difference between Internal Trusted Storage (ITS) and Protected...
I have encountered a problem with I2C bus on the nRF54L15. BMP390 sensor is connected to nRF54L15-DK by the i2c bus. if i try to brake the line and recover it agane, the connection...
In nRF5 SDK, we configure GPIO wakeup sources for System OFF using `nrf_gpio_cfg_sense_input(pin_number)`.
What is the **exact equivalent API/configuration** in **nRF Connect...
