Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I'm developing firmware for a custom board developed with the nRF5340. We opted to use RTT as our logging/shell output as opposed to UART thanks to pcb size limitations. I...
Hi,
We are porting some of our old firmware from SDKs <= 17x to nRF Connect SDK.
We have not found a way to access several of the drivers, like pwm_nrfx.c and use functionality...
Hi,
I'm trying to build the nRF5340 Audio sample application for the nRF5340 Audio DK board and get this error message when creating the project:
Any thoughts?
Regards...
I'm trying to migrate from the nRF52832 to the nRF52833 using the same exact code, but the nRF52833 does not go into low power mode. The nRF52832 consumes 100uA with the nRF52833...
Hello, I have successfully connected two NRF5340s using central_uart and peripheral_uart and can send messages to each other. But I don't know how to test the data rate.
I have an implementation that is using a PWM output to drive a LED. It has been observed that when the LED is on in a constant drive state, fixed PWM output train, the LED...
I would like to communicate at a speed of 1ms or 2ms if possible, as I need to make a gaming mouse with as little latency as possible. To achieve this, I plan to use the nRF52840...
Hi Team,
could you please help us how to remove service change characteristic?
Also please share us how to SET PHY as a constant "BLE_GAP_PHY_1MBPS" ?
please suggest...
The following code got NRF_ERROR_INVALID_STATE. What is meaning of NRF_ERROR_INVALID_STATE? And when will NRF_ERROR_INVALID_STATE generated?
err_code = nrf_drv_gpiote_init...
Dears,
The customer wants to know that the Thingy53 evaluation board can calculate the 3-axis acceleration,angular velocity,magnetic field, these 9sets of data into "quaternion...
I want to remap SPI0 pins from default (P26, P27, P28) to another ones (P08, P09, P10) on PCA10040 under nRF Connect SDK. But I stuck into a problem: SPI module seems to work...
Hi,
I just go a question about when to use the nrf_moden_lib_shutdown(). Is it necessary to use in this code case? Since I've used lte_lc_power_off().
Regards,
Elia...
Hi
1. I tested function NRF_LOG_INFO and found that NRF_LOG_INFO automatically prints the \r\n character
2. How can I remove the \r\n character
Thank you for all...
Hi ,
i am able to find the api related the reset cause" hwinfo_get_reset_cause". But i need to check this api for the Brownout reset ,Poweron reset and Watchdog reset...
HI,
I need to understand the working of USB RNDIS and how zephyr is supporting that feature. Do we have any documents or example for the same ?
Currently I have BL653_dvk...
