Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
Hi, I use AT command controls the GNSS use Serial LTE modem example in my 91DK board.
I send command as below example,
but my uart tool receive as blow, and i don't...
What is the difference between nRF 5 SDK (downloaded in .zip format) and nRF Connect SDK v1.9.1 ?
I am using VSCode through nRF Connect SDK v1.9.1 and I find it easy to...
I am connecting a nrf52480 board (Adafruit Feather nRF52840 Express) as Connectivity chip and a custom board as Application chip for Nordic serialisation. Able to establish...
I am connecting a nrf 52480 board(Adafruit fether express) to a custom M4 cortex board with the help of nordic serialisation library. I have ported the serialisation library...
Hello all!
I'm using nRF52-DK to develop program which is controlled by smartphone (BLE) and do ADC&GPIO in the circuit.
GPIO acts like this: High-Low-High-Low.... it...
Hi Nordic,
I am working with nRF52840, sdk17.1.0 and do the following test:
I use nrf_gpio_cfg_output(), nrf_gpio_pin_set(); to set gpio P1.00 to high and use nrf_gpio_pin_input_get...
Hi Nordic:
Test with board nrf5340-dk ncs v1.9.1
prj.conf
# Console
CONFIG_LOG = y
CONFIG_LOG_PRINTK = y
CONFIG_LOG_DEFAULT_LEVEL = 3
# UartConsole
CONFIG_UART_CONSOLE...
Good morning:
I'm trying to develop the twi_scanner with the nrfx libraries. Everything seems to compile fine, but at the end of the Build process I get:
d:/ncs/v1.9...
Hi All,
I have a nRF52840 DK board. Which I bought about 1.5 years ago. I used to do some development using Segger Embedded Studio those days.
Now I have setup the Zephyr...
Right now there are 2 supported codecs: SBC and LC3. It also looks like that they are implemented in software.
Can we have other audio codecs (i.e. LC3plus HR, aptX or LDAC...
