Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hello,
I am new in nordic previously I was working on Cypress controllers. I am trying to put the device in System ON Low power mode.
I have tried the below functions...
Hi,
I am working on a project using BT Mesh and I am evaluating a prototype using the nrf52840. I am not working with the mesh-SDK, because I am using zephyr. I am working...
Hi, I have a University group project which required us to build software on Android devices. Basically, this project requires us to build software based on BLE Mesh between...
Hello,
I want to communicate one card nrf5340dk with 2 same card in using 'central_uart' and 'peripheral_uart' samples.
I have succeeded to establish the connection and...
Hi,
We have a new product and are looking into OOB pairing for authentication and encryption. All the information about OOB flows back to NFC pairing, but that is not what...
Hi
I am working on an application that uses extended periodic advertising feature of BLE 5. In this sample (periodic sync):
https://github.com/nrfconnect/sdk-zephyr...
Hello nordic. I have several SPI peripherals connected to the nRF9160. I'm using the PPK2 in ampere mode. Does this then also measure the additional current drawn by the SPI...
Hello,
I'm wrapping up the layout of a board based on the NRF52832 (DCDC). I've tried to replicate the reference design as close as possible. I'm using Kicad and had to...
Hi,
Referring to the case,
https://devzone.nordicsemi.com/f/nordic-q-a/72660/nrf-connect-sdk-v-1-5-0-how-where-to-change-phy-and-tx-power-for-long-range-application
...
Code is based on Nordic UART Service Client sample on nRF Connect SDK v1.8.0
I am trying to create several client connections for different servers. The code is incomplete...
Hi Nordic team
I tried SDK Connect v1.8.0 ble_peripheral_lbs_coex sample.
It found advertising signal was very weak. The distance between PCA10112 and my phone was 1 meter...
I use PPI for ADC and GPIO pulling. When I connect and then disconnect - nrf52840 not advertise until reset the SoC.
I can connect after reset. But when I disconect then...
I am used to using Segger, but am switching to west for various reasons. The main reason is to create a CI/CD pipeline.
I built a sample project with west, didn't see any...
Hello,
I am new to embedded/BLE development so forgive me for my ignorance on some of these topics. I am creating a fairly simple BLE Peripheral Server device that has a...
