Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
We have a running sensor system with four sensors sending data to one central node (all nRF52840 Dev Kits). The nRF Mesh App was used to provision the nodes.
Now when...
Hi,
I use NRF52832,SDK17.1 ,softdevice is s132.
I shielded the part I added by myself in ble_uart example, but it will prompt this error about 1min after power-on. How...
Good Morning and a Happy New Year,
I try to test an application, using the nRF Connect for Desktop (on a Mac). While trying to pair with an application that supports LESC...
Hello All,
I've had some success now connecting my 52840 Dev Kit with the NRF52840 Dongle and would now like to use the dongle as a receiver with the PC-BLE-DRIVER-PY library...
Hello,
Does the nRF Connect SDK support enabling QSPI encrytpion (DMA, XIP)?
I see there are two functions in the nrfx_qspi.c that do this: nrfx_qspi_xip_encrypt and nrfx_qspi_dma_encrypt...
Is the nRF51 SDK version number exported as a preprocessor #define in any of the SDK header files?
Because the SDKs are not backwards compatible to different revisions...
Hi,
I designed a bluetooth device that stores 8kb of data. With 20ms connection interval, data is sent to the smart phone in 3 minutes which is to high for this project...
Hello.. I want to access the nRF5340 registers to maniulate there values, for example : If, I want to acess the PSEL.RTS register or CONFIG of UART0 to initialize these. How...
Hi.
I am following the tutorial "Developing Matter products with nRF Connect SDK" but having problems getting the openthread border router working with the raspberry pi...
I am using the board with MQTT simple software
when I am activating one a signle EVB, it works well
however when I am activating on two board in the same general location...
I noticed in Zephyr OS there is an API LED:
led_on(dev_io, RED ); <-- does not work gpio_pin_set(dev_io, RED, 1); <-- works well
what can be the reason ?
can you...
Hello everyone. I have just started with the eval board uBlox NORA B1 (NORA B-106) and I am trying to find a starting point for streaming audio via Bluetooth Handsfree protocol...
Hi Nordic：
I use the LWM2M of NCS and found that the power consumption increases every 2.5 seconds. I use the monitor to find that the serial port is sending data. How...
We are attempting to deploy a system consisting of one nRF52840 devkit running the multi-NUS example app, and over a dozen custom boards based on the nRF52832. It all works...
