Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
I have been developing code for this chip for a while now. In the beginning, I was using the end device role but after a couple of months, I decided to change it...
I'm getting the following linker errors after switching to the latest version of the SDK (17.1.0). I believe I've included the files that define the offending macros (for...
I've made a basic QSPI setup for an MT25QU512. By default the QSPI driver is using 24-bit addressing. To access all of the memory, I'd like to set up the QSPI driver to use...
Hi,
Currently, we have a device that uses the nrf52832 custom board as a Peripheral notify to send the data collected to Pixal 5 (central),
We have a cellphone app to...
Hello Nordic / Zephyr experts,
I am looking for AT command parser for the UART of nRF52840. Want to send and receive AT commands to a LTE modem using MQTT messages. Need...
Hi,
I am aware that nrfutil does not work for OTA updating the nRF53 and was wondering if there was a similar tool that will allow me to achieve this? I need to update ...
Dear BT Mesh experts,
What's the advantage/disadvantage of using the nRF5 SDK for Mesh compared to the nRF Connect SDK ? Consider a rather simple BT Mesh device that provides...
Hi support Team,
Is there a way to make the nrf52840 to connect with only given MAC address (i.e., a MOBILE) ? The MAC address (i.e., a MOBILE) will be changed dynamically...
Hi Support Team,
What's the UBM pad diameter of nRF5340-CLAA?
BTW, any correlation between it and label 'b' in Mechanical specifications in PS?
Best regards
Sal...
When I try to open the .overlay file in SEGGER it shows me an error : "Can't Read file" with the message "Can't open xxxxxx/xxxxx/xxxx.overlay for reading.
Has anyone else...
Hi,
I am running Homekit over Thread sample(NCS/Homekit tag v1.7.0 using MTD-SED conf) on my custom board and I found that the QSPI Flash (MX25R64, as same as the one use...
I want to test OTA in button mode. I have configured the button in DFU project. Now I upload the files in my device in the following pattern:-
1)Bootloader hex file
2...
Hello,
I have an nrf5340-dk board and I am trying to play around with the different baud rates through changing the overlay file (as shown):
I am using teraterm...
Hi guys,
After weeks and weeks of trying with 3 different boards (Thingy91, nrf9160DK and Custom board), combination of different LTE Antennas, Bell, Hologram and iBasis...
I am using nrf52840's dongle development software, and I found that when the slave device sends LL_SLAVE_FEATURE_REQ , the host will return LL_UNKNOWN_RSP. I want to know...
