Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi while implementing/testing MTP on Linux Wireshark captured setup requests asking for "Device Qualifier Descriptor" according to section "9.6.2 Device_Qualifier" in the...
Hello,
Can you please provide information for current consumption of the GPS in these modes?
VDD=3.8V
Acquisition time = ? seconds
Acquisition current = ?mA
Tracking...
Dear all,
For our project we want to store information on the device in an additional flash partition. We have created a new flash partition, called factory_settings_partition...
Helo Nordic support team,
I am supporting a client that has designed a product using the NRF9160 with GPS. The product has a small patch antenna mounted on the pcb board...
Hello. I am trying to build an project and I need to use RF module. And I have to Use pic18f45k22 with MikroC. But I couldnot. I have some 18f45k22 codes but dont work I dont...
Hello,
I need to retrieve the IP-Address of the modem, are there any convenient way I can do this?
AT commands maybe?
Appreciate any info on this.
With regards...
Hello
I am having rather odd problem with SWDIO pin shorted to ground. I am using Fanstel BT840x BLE module and I have never seen this issue on my custom board until last...
I see this line for cache enable register in application domain : infocenter.nordicsemi.com/index.jsp
NVMC built-in cache not supported (ICACHECNF, IHIT and IMISS registers...
I'm trying to test button less dfu on nrf 52840 dk. i am simply compile that hex ble_app_buttonless_dfu_without_bonds_s140_with_setting_page.h file with soft device s140 or...
I am building the coded bluetooth gateway using nrf52840 and ENC28J60. Integrated between two examples:
https://github.com/nrfconnect/sdk-nrf/tree/master/samples/bluetooth...
Hi to everyone!
I am working (with Keil uVision) on a custom PCB that includes the NRF52832 (MDBT42Q module) and some sensors from MAXIM INTEGRATED. There is a Sensor Hub...
Hello, I was told to make a new ticket after commenting on this ticket .
I am using SDK 14.2, S140 alpha, NRF52840. Segger IDE. I have been developing with this IDE & SDK...
Hello
I want to transmit location data to website using udp, the examples udp and gps are very good and I need combine in only one project but dont understand what files...
Hello,
The product specification for the nRF5340 peripheral chapter here mentions " The application core peripherals are accessible from the network core".
However in...
Hello I am using ncs version 1.5.0 .We are using nrf9160 dk version 0.15.0 & 1.0.0 for our development.Whereas we observed some issues like the network latching time is getting...
