Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I have an nRF5340 DK board. I have followed the online installation instructions and *believe* I have successfully installed (win 10) nRF Connect and Segger Embedded Studio...
Hello, I'm routing on the nRF52833-QI. I want my RF track (ball H23) to go without bends. I don't use J24 ball. Can I remove the ball J24? What is your suggestion? Best regards...
Dear Sir,
Moving to zephyr new installation 1.4.99
The code of getting the IMEI number no longer works.
Modem firmware is mfw_nrf9160_1.2.3
reply_buf_len = at_exec_reply...
I'm trying to connect a 52832 board to a peripheral BLE device. NRF52832 SD: s132 v7.0.1 SDK 16.0.0 As a first step, I'm not setting flters, I just want to connect to any...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice 6.1.0. We are able to perform a DFU for our application by downloading the .bin and .dat files...
The nRF53 data sheet defines the minimum clock period for teh SPI slave and master as 125nSec - which equates to 8MHz. The SPI Slave also gives the max data rate as 8MHz with...
I tried out a ble_app_hrs_freertos_pca10056_s140.emProject and was able to compile but a couple of questions:
- how is heart rate info calculated? where's the sensor even...
Hi,
I want to write to the NVMC UICR Customer[n] memory addresses during code execution.
I noticed that I can write/read/erase those addresses only before the initialization...
I am testing an example from nRF SDK 7.2.0 on a custom board with nRF51822 QFAAH2 chip. This simple example is ble_app_template adapted for Segger, it should advertise and...
At boot-up of the Zephyr kernel drivers are loaded by default.
Is there a way to change this? I prefer to load the drivers depending the board configuration.
I can see...
We're developing a product using NB-IoT, lwm2m and the nordic nrf9160 mcu.
What we're observing ist, that using the latest nordic connect sdk, multiple lwm2m ressource notifications...
Hi，I have program the hex file "nrf52840_xxaa_pca10056_uart.hex" into my PCA10056 board, But t he first device is not created (as a leader)after clicking "start scan" button...
Hello everyone,
I am currently using the Nordic-Thingy-91 to test the nRF9160 and other components on the board. Now I am trying to implement a simple motion detection with...
Hello, I am trying to debug Zephyr hello world example on an nRF52840 DK. For my setup, I am using eclipse with the zephyr plugin . Following the plugin readme documentation...
I'm learning whitelisting with the HID Keyboard Example nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_keyboard\
Question - is there a way to create a new...
