Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
When working with AT#XHTTPCREQ we have encountered the following provlems:
1. Sending AT Command `AT#XHTTPCREQ="POST","/upload","Content-Length:3357",3357` with the payload...
HI!
I'm currently working on a project where I'd like to send and receive BLE messages using my own channel hopping mechanism.
I've read into the 17.0.2 Examples ...
I am having trouble connecting to an nRF52810 in a uBlox BMD-330 Eval Kit.
It has previously been successfully flashed with custom firmware but, now, when I try to connect...
The specifications for Flash programming in section 4.3.7.1 page 21 is blank in the nRF52810 Product specification 1.0. Can you please provide the values for this table?
Hi all,
I am not able to update the modem firmware over usb/mcboot with the programmer on my Thingy91. I have tried both on linux and win 10, the problem is the same. The...
Hi,
I have been using the NUS on nRF52832 DVK with no issues, however, when I migrated to the nRF52840 DVK and a custom board based on the 52840, the NUS characteristics...
Hello Nordic Community,
I am currently following the SMP guide provided here: https://docs.zephyrproject.org/latest/samples/subsys/mgmt/mcumgr/smp_svr/README.html
The...
Hey,
I am wondering if it is possible to run MTD and SED on the CoAP server on nRF Connect SDK v1.4.0.
I have looked at the question " How do I set up CoAP Server whit...
Hello,
We are going to design our new product using NRF52832. Please suggest if there is any other better IC which has higher transmission range, higher RAM and with less...
there is a module in the skylab project on the nRF52832 chip and it does not agree with the tablet, which is old BT. Is it possible, through the firmware or SDK, to downgrade...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
