Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi Team,
We are going to use nRF52833 chip-set and we need the below information based on this input we will decide our chip-set.Kindly update your support.
1. What is...
Hi ,
The size of the boot loader partition 24KB is fixed for the lifetime of the device or it can be extended, as we have some feature to add like firmware update.
Firmware...
Hello,
I read through the datasheet of the nRF85832 to understand the peripherals a little bit better, but I got stuck while looking through the register overview (in this...
I am using NCS-Zephyr, Zephyr version 2.3.0-rc1. If you need to know the NCS version too, please can you include how I can find this?
When I do west flash normally (which...
Hi Team,
We have requirement for firmware update over Ethernet [ external Ethernet ENC28J60 module interfaced over SPI] 1. Is bootloader customizable for adding SPI driver...
Hi all,
I'm working on a project which I started from the multiperipheral example. I am using SDK 15.3.0 for this. I am developing the software on the nrf52840 DK using...
Start SEGGER Embedded Studio by clicking Open IDE //Successfully installed, what means Open IDE ? ? ?
Select File → Open nRF Connect SDK Project… //it just dont appear in...
Hi,
Currently, I am in a feasibility analysis stage for an application which requires BLE Mesh with Localization (RTLS using AoA and AoD). I explored SDKs for nRF52833...
Hello,
on SDK16, with nrd52dk, with android phone, standard ble_app_uart example works fine with nRF Toolbox. But when I disconnect from nrf52dk, the chip still thinks the...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I changed the device name while not connected.
but, The...
Hello,
I am trying to follow the tutorial SDK UART coexistence example , but it seems like the last step cannot be completed. As you can see, that .hex file does not exist...
I am working on a low power peripheral project (similar to the Nordic blePeripheral/uart example). I'm going to be using an nRF52805 with SDK 17 and s112. I found the Apple...
Dear all,
I have tried my best to find answers in questions posted previously but I still have a few questions that I would like to clear up. I will keep it concise. Thank...
I want to configure the UART1 (not the UART0), and I want to know if there have some examples that introducing the UART configuration by directing accessing the register....
