Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
I am using ncs 1.0.0 and Modem FW version 1.0.1.
I am using UART 2 and i have kept UART TX and RX port 0.11 and 0.10 in overlay file.
I want to change the port pins...
Hi,
Our team has identified an opportunity that your nRF52832 fits well, I am having a difficult time getting started with your Bluetooth SDK and reaching out for assistance...
Hi,
As simple as the title! I have tried to move my code from sdk v 3.1 to v3.2 but it will not join the network.
Back to basics and using off-the-box ligh switch example...
Hi
I have been working with the nrf52832 breakoutboard from sparks fun and the nrf52 10040 Dev board.
I want to work with SPI communication in order to intergrate an accelerometer...
I'm having an issue with some iPhone11's, where under certain conditions the iPhone11 is sending two consecutive Link Layer requests with a Control Opcode of 0xFF. The SoftDevice...
Using zboss_start_no_autostart() instead of zboss_start() will cause a power consumption of 630uA. I was expecting the device to be sleep and in a very low power mode.. All...
Hi
When I use the nRF5_SDK_15.3.0, the nRF52832 cannot enter low power (about 900uA). The example is file ble_app_blinky.
The main code is as following:
int main(void...
Hello,
I want to blink the LED by pressing button on nRF9160dk. Is there any sample available to start with?
I started with button demo but on button press there is no...
Hello,
I am using SDK 15.2, could someone please tell me the location of pstorage.h file in the folder. (I found pstorage._platform.h but I cannot locate pstorage.h.)
...
Hi nordic,
I am developing with nrf52832, s132,v15.2,0.I am using secure dfu bootloader. But its connecting in nrf_connect app, after connected, i got this below mention...
Hi,
I'm wondering if you will support sending data using control plane (CIoT EPS Optimization using CP) and Non IP Data delivery for CATM . I assume you will do it for...
Hi:
I am running the example program ble_app_att_mtu_throughput on the SDK52 for the NRF58232 and the NRF58340 next.
My question has to do with how to modify the example...
I'm trying to simplify the open_bootloader example from SDK 15.3. I'm getting rid of version, signature and keep only the CRC validation. I'm actually trying to understand...
Device: NRF52832_xxAA Softdevice: S113 v7.0.0
Hello.
Sometimes, during firmware running, I get a fault from Softdevice with pc: 0x0001A990. Could you inform me what causes...
