Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello Forum,
I am now working for a year with the nrf52832 and whenever I had a software problem I found a solution in this forum so thank s for that :).
However now I...
Hi, I have just set up the nRF52840 DK to advertise in Bluetooth 5.0 successfully but I am having difficulty changing the initial preferred PHY to Coded (Long Range). I understand...
Hi, I have NRF52 issues creating one hex file containing softdevice + app + bootlader + settings. The device does not boot up. But if I have flashed the softdevice first then...
We are using nRF51822 and is considering update to SoftDevice S130.
There are two things we currently investigation:
1. Support security.
2. Increase MTU (possible)...
nRFConnect sees the j-Link device, and everyone else sees the device.
I use this j-Link with Segger Embedded Studio.
What makes nRFConnect unhappy? Perhaps python2...
Does nRF51822 support uart over ble profile? I see in previous discussion "nRF8001 UART-over-BLE" talking about this and answer suggest 51 serial has this?
We want add MQTT...
Hi everyone.
I have problem with my device. I use Visual studio with visual GDB and I'm trying to use interrupts from RTC. Got from this site lot of examples and wrote some...
Hi,
I am running my nRF9160 DK in "nRF Only Mode" (Via SW1). I would like to drive the serial terminal out via one of the GPIO pins, connected to my MAC using an FTDI serial...
SDK v15.2.0 using peripheral spi example. Windows 8.1, uploading to nRF52 DK.
In my while loop I use bma_spi_read() twice with a small delay in between. The first...
Hi,
I am using the reliable message communication to measure Round-trip time based on the Light switch example.
I noticed that in high traffics, some packets are not...
I want to use TimeSlot API for nrf52832.
two question.
I want to use time slots regularly . I call follow, timeslot_open() timeslot_request() - timeslot_end() -> IDLE_STATE...
Hi there,
I've already asked about it https://devzone.nordicsemi.com/f/nordic-q-a/49701/commissioner-disable and I've tried it but nothing work. I've already spent 5 days...
I am in pre production with the nRF52840. My customers have access to the micro USB port on the device. I want them to be able to define a string for the nRF5 transmitted...
I am using nRF51, SD 130 1.0 and SDK 10.0.0. I have 11 buttons connected to nRF. Currently it only works for up to 4 buttons (APP_TIMER_OP_QUEUE_SIZE is 4, but I'm not sure...
Hi,
i am working on spi master example in nrf52832, when clock is set to 8MHz, clk signal output at the nrf52 pin is more like triangle wave.
is there any way to set pin...
