Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I compiled 4.0.0 in the past and the generated libraries were named "pc_ble_driver_shared_sd_api_vX.dll".
Now I compiled 4.1.1 and the libraries are named "nrf-ble-driver...
Dear Nordic:
My nRF82832 codes based on nRF5_SDK_15.2.0_9412b96 and used s132_nrf52_6.1.0. But I find the Bluetooth signal of nRF82832 can’t be scanned by smart phone which...
Dears,
I am using DK PCA10028 (V1.2.2). Start developing from SDK_12.3.0\examples\ble_peripheral\experimental_ble_app_blinky.
All system configuration keep the same (ADC...
Hi,
I'm using:
nRF52840 Preview DK
Zigbee v2 (nRF5_SDK_for_Thread_and_Zigbee_2)
Segger Embedded Studio for ARM 3.52
Developing on a MacBook (macOS Mojave v10.14...
2017-04-12T06_05_42.374Z-log.txt
Hello,
the example "experimental ble app cgms" (SDK v13.0.0) failed to pair with nRF v1.1.1.
The error code was Authentication failed...
Hi, guys. I'm using two PCA10040 boards. One is using the ble_app_uart__saadc_timer_driven__scan_mode example
github.com/.../main.c
and the other board is flashed with...
Hi,
So I've been trying to get the SIP down to use its most minimal power consumption level to the claimed floor of 7uA or so (I'd take 20uA even), and have stripped the...
Hi everyone, I am using nRF52832 (PCA10040) and ICM 20648. I want to write a I2C aka TWI interface to read accelerometer and gyroscope readings and print them out with TeraTerm...
Hello,
Does anyone know if I can use J-link BASE for programming in factory. I haven't seen any limitation related with it why can't use it for production purposes but If...
Hi,
In app design stage, and we cant connect to the bluetooth device UNLESS GPS is actually on. I dont mean permission, that's fine, I mean actually having the gps service...
Hi, I just started to develop a new project with nRF52840 and I've been trying to understand about white listing feature of BLE.
As I need white list to skip unknown device...
Hello everyone,
We are using the nrf52832 Dev Kit ( PCA10040 1.2.1 2017.49 682663245)
SRK Version 15.3
OS : Fedora
On the saadc example in the peripheral folder...
Hello,
I need to convert a standard 32 bit floating point number to IEEE-11073 16-bit FLOAT with 12-bit mantissa and 4-bit exponent (source: https://infocenter.nordicsemi...
Good morning,
I have been asked to merge the code developed by two independent teams. Of course, each one of them took their decision on the management of time, and of course...
