My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
I've been learning to use the PWM.
This should set the PWM up for a period of around 250ms
After the period is over I expect to clear pin 23.
I find that its cleared...
Hi All,
In nRF52 SDK 15.3.0 , example ble_app_uart in peripheral mode, i have changed the TX characteristics which is initially of type (notify) to type (read ). I am able...
Hi community, I have a problem establishing a connection with more than one device in the MQTT client example (MQTT/6LoWPAN/BLE). I'm using:
SDK v15.3.0 (also nRF5 SDK...
Hi,
I'm trying to connect my nRF52840 SoC to nRFgo Studio on my Windows 7 Laptop using the usb connection on the nRF52840, unable to see any data about the connected board...
Hello everyone,
I need transfer large data 12KB array send central to peripheral using nrf52832. I try this examples in central (ble_app_uart_c) and peripheral (ble_app_uart...
Hi,
I am using nrf52840 with custom board, sdk 15 and and softdevice 6.0.0. I modified saadc example to sample SAADC value once and stop it in saadc_callback. Everything...
I would like to know, what is the correct workflow with Alarms ZCL cluster?
There are no examples with it in SDK (at least, as I have seen). The documentation on this subject...
Hello,
We have started to design a project and we would like to use the Nrf52840 as border router with a linux terminal. The link would be a serial over USB. So the NRF52840...
Hi,
I'm trying to create with the S132 SD on the nRF52832 an application, that will provide 3 different kind of sensors. My goal is, that these sensors will appear as an...
Hi there, I could not find any documentation about the meaning of the version numbers, when creating bootloader settings:
nrfutil settings generate --family NRF52840 --application...
Hi
I am working on Eddystone in nRF52832. Its working fine when using power supply.Then I used Lithium battery as VDD. then it not working properly, only working in connectable...
Hi,
I was wondering what is the recommended GPS circuit would be for an always outdoor device with a large patch antenna, without the need for an amplifier. Would the following...
Hi all,
I have my custom nRF52832 board, I use SDK12.3.0 with SD132.
I'm currently trying to add BLE advertising to my firmware. To achieve that I'm copying parts of...
Hi,
I am performing the following test:
https://devzone.nordicsemi.com/nordic/b/blog/posts/testing-long-range-coded-phy-with-nordic-solution-it-simply-works-922075585...
For my graduation project i'm developing an improved version of the Nordic Secure DFU Boot loader. I'm trying to integrate something like the Zigbee OTA client inside the...
