I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi , nrf connect V.2.5.0 in windows 10 64bit, fails to launch Bluetooth low energy app. "DEBUG UART read operation on port aborted" is the log info which i came to know from...
Hi,
I have a BLE sensor node (firmware not modifiable) that takes up a peripheral role and starts advertising when powered up. Typically, one can scan for the node from...
Hi All!
I have been working on bringing-up a custom manufactured nRF52832 board. I have with me 6 boards, the first 3 are working fine, the other 3 are not. In both cases...
Hello all,
I'm practicing creating my own service following instruction from this link: https://github.com/bjornspockeli/custom_ble_service_example
Now I stuck at part...
Hi everyone,
I have configured two UARTES , one using the app_uart library and another using nrf_serial library.
I am using SDK15.0 alongwith s140 softdevice with bluetooth...
Hi There,
What are the difference between system off, ram retention, RTC wakeup vs system on with ram retention, RTC wakeup vs FreeRTOS tickless with RTC wakeup? And what...
Hi team,
I noticed a very interesting incorrect pin description in the latest product specification of v1.2 for nRF52810, QFN32.
Above picture shows we have 2 p0...
I'm using the PCA10056 with an SD card connected via P1.12-P1.15. When I use the FatFs example of SDK12 PCA10028 it works fine. but when I use the FatFs example of SDK15.0...
Hello,
I've got the nrF52840 and would like to create a simple application to send temperature to my laptop. Then the next step would be to create some mesh network with...
Hello,
I am working on Custom BLE HID Keyboard. I am currently trying to understand working of program given by nordic in SDK-10.0.0. THere is one problem which I am facing...
Hi,
I've tried to implement the DFU_buttonless example to my development board. I programmed the bootloader and the settings-page. The bootloader detects the application...
I'm currently in the prototyping phase of getting two nDK52840 boards talking to each other. I currently have one board flashed with the central role, and another board flashed...
Hello.
What do I need to run this example called uart?
As far as I understand this should be simple echo program meaning what comes in goes out but I can not see anything...
I want to use nRF52-DK for receiving data over UART and send it over BLE link so I loaded the ble_app_uart but hard fault occurs immediately in these circumstances - 1. If...
