Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I´m using nrf52832 with sdk 14.2.0 and softdevice s132.
I'm trying the example bootloader_secure_ble and compiles me correctly.
The problem is that when I debug...
In a documentation i read that i can transmit power at minimum of -40 dBm ?But i cannot achieve my target as my range has to be minimum of one meter?
So how do reduce the...
After getting SDK 12.1 and the S332 v2.0.1 softdevice working, I started working on updating the bootloader from the S132 bootloader we've been using to supporting the S332...
I am trying to set up a humidity sensor over I2C and I'm trying to use the twi interface. There are examples where the app_twi interface is used. I am however unable to get...
I'm working with a development prototype board with the nRF52832. It is connected to a main processor in our design over UART. We are working towards being able to do the...
Hello Nordic team
I am working on nRF52840, SDKv-15.0.
Is there any example code available which can send message from central device to peripheral device apart from ble_app_usrt_c...
Hi,
I'm tring to enter DFU mode by combo keys by KEY_COMBO_TWO_KEY_REGISTER().
In v1.1, I used m_pwr_mgmt_shutdown(M_PWR_MGMT_SHUTDOWN_TYPE_DFU) to enter DFU mode directly...
I'm looking at decreasing the motion sensor update rates for the Thingy:52 to get less frequent readings into the sample app. I have seen in the MPU9250 specs that I don't...
Hello Nordic team
I am working on ble_uart_c central example on nRF52840 DK, SDK v-15.0.0. Example code working correctly I can exchange data between peripheral and central...
Hi I am trying to reduce the power consumption of the badge of my company as much as I can. We use a proprietary radio protocol on the nrf52832.
I'm currently developing...
I have SD and BL secure flashed to the device, and now trying to get the second part of buttonless_dfu + app with settings flashed next. After flashing the second part, DfuTarg...
I'm attempting to optimize our application for battery life on the nrf52832.
If I execute a floating point calculation to rescale RGB to PWM, I start drawing 6.2mA, eliminating...
Dear all,
We are programming the FICR and have found very little documentation on the random number generator fields: - TRNG90B.BYTES - TRNG90B.RCCUTOFF - TRNG90B.APCUTOFF...
Hi
I have followed this example: https://github.com/bjornspockeli/custom_ble_service_example through to the end, but am now having issues with some intermittent behaviour...
