Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi Forum,
I have just purchased nRF52840 Dongle and trying out “Blinky” application from source SDK “nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\peripheral\blinky...
Hi:
I want test the bluetooth function of nrf52840 pca10056. but After compiling the ble_app_uart test program, use nRF Connect tool connect to PC. display "connected"....
I made this question earlier, however, after receiving emails about "an engineer has been assigned" and "the ticket has been replied to", I can't access the question. The...
Eclipse wont run ble_app_buttonless_dfu. I just get a "No source available" error message, it won't go to the main.c source. I have created a virtual folder with link to the...
Hi all,
I have been using nRF devices since a long time but recently I stumbled upon a problem statement where I need to create a mesh network. Here I have to have a master...
Hello, thank you for taking time to review this. I am trying to setup a serial DFU setup for the nRF52 on the nRF91 DK board. I am running into problems getting it to work...
In the nRF Toolbox I found this Beacons option where i can update the UUID , Major and Minor of the beacon. How do I use this functionality of nRF Toolbox app?
Hello, I'm not very famililar with Airfuel, but I want to add in my device wireless charging function. I start searching solutions for this challange and I found Airfuel and...
Hi
I am facing problem with segger. Project get compiled and able to program hardware but hardware is not working until debug process is start. After put hardware in debug...
Hi,
I am trying to establish UART communication between two nRF52 Dev boards. I flashed both of them with UART peripheral example from 15.2.0 SDK and connected TX,RX and...
Hello,
Recently I'm working on the project that utilizes the nRF chip and the external memory MX25R3235F. The SDK is 14.2.
I'm trying to configure the peripheral and the...
Hi I am using nrf52832dk as master and slave for spi communication. I want to send below data over spi. 0x8000000008 0xEC000100C5 I am get confused in transfer function of...
Hey,
referring to my previous thread in https://devzone.nordicsemi.com/f/nordic-q-a/44298/running-usbd_hid_generic-in-nrf52832-using-a-custom-usb-module-mcp2200 . so am...
