Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi, I'm trying to use SPI to control an RF module to send audio data from one microcontroller to another. The parts and software I'm working with are:
NRF52 Development...
I'm using SDK 15.0 on an nRF52840 dongle. I've been able to retarget the output functions (outputting through the CDC UART) but so far I can't seem to use getchar() in my...
According to the Online Power Profiler , the Standby time between Crystal start-up and Start radio is ~1 ms; however, we measure a variable amount of time between 0 s and...
HI All,
i m new to this technologies.Now m using NRF52840 DK and sdk as nrf15.2..we have developing the nrf52840 as a beacon scanner to scan the ibeacon details like rssi...
I'm using a Nordic dev board (PCA10040, nRF52832) with modified "Nordic_HRM" firmware sending packets of 20bytes at 100Hz over Bluetooth Low Energy.
I'm using Nordic's heart_rate_collector...
Hello everyone! I have followed the tutorial " Installing a 6LoWPAN enabled Linux kernel and required modules" and i have compiled the UDP client IoT example in order to test...
Hi everyone,
I am using nRF52 which has 52832 on it. Currently, I am working on 2 nRFs and one RPi with MQTT on the softdevice 132. One nRF is the publisher, another one...
I am using pcaboard10028 ,sdk12.3.0 and softdevice s130. I am using proximity example to read battery percentage level,so giving adc input as following:
channel.config.config...
Hi, I'm having problem with UART communication. I use basic UARTE code and I want to send simple data to PuTTy terminal. The problem is whatever I would send i get only 'K...
Hello!
I'm trying to update the bootloader of a nRF52 device OTA. We are using SDK 12.3. The device has our own application flashed, along with what is essentially the bootloader...
Hi Sir,
We want to know about AoA /AoD applications for 52811, and there are some question as below.
1. Is there a difference between BT 5.1 and BT 5.0 from the perspective...
Hi,
I'm implementing quadrature encoder to read motor speed/position. So far I configured a gpio pin where A channel of the quadrature encoder is connected to capture timer...
Hi, I'm now using nRF52DK with Keil and have followed the getting start manual in the Nordic Devzon.
Till now, I completed UART example and want to add ADC function to this...
