Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
How can i sample nrf52 own input voltage to do battery measurements?My nrf52 chip is directly connected to a battery and it needs to sample its own input voltage without a...
I have been searching through the info center and can only find the slightest mention of the bsp_board functions.
Could someone help me, locate the right page documenting...
hi sir
i have start my project in NRF52-DK development kit but some BLE card give me data in three channel and i have received all data and give me same like data pls find...
I'm new to use nordic. I am using thingy 52. I would like to add a new custom feature that communicate text via BLE from app, store the text as userid in the thingy and check...
i use 52840, nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_msc this example, and change the log level to debug
but i still can not see the DEBUG output information, this...
Hello.
I developing drone by nrf52832.
Developed based on nrf52-quadcopter .
physical web & drone is service uuid as below.
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hello, I'd like to connect the nRF52840 to four I2C sensors. These sesnors may or may not have the same address and they will all be at the end of their own 2 meter long cables...
Recently, the side-channel attack "Screaming Channel" was described in a paper ( http://s3.eurecom.fr/tools/screaming_channels/ ).
The authors demonstrate a remote, passive...
Hello Nordic team
I am working on nRF52832 DK and SDKv-11. Can we increase MTU size to send more than 20 bytes in one packet? If yes then any example code do that?
Is...
i use SDK11.0 in 51822, I just need use BSP_BUTTON_1 interrupt, don't need BSP_BUTTON_0 interrupt, but i must initial BSP_BUTTON_0 interrupt, otherwise the current will be...
Recently, the side-channel attack "Screaming Channel" was described in a paper ( http://s3.eurecom.fr/tools/screaming_channels/ ). The authors demonstrate a remote, passive...
Is it possible to setup a mesh network over BLE and use 6LowPan to enable the use of the IPV6 address space?
The goal is to setup a network without using a star topology...
In order to change the bitrate of the nRF52840 I tried to change the following code on advertiser.c :
static inline void set_default_broadcast_configuration(broadcast_t...
I programmed a PCA10001 with the HID Keyboard example and changed the preprocessor code from NRF6310 to PCA10001. The functions were tested according to the online HID Keyboard...