Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
i am trying to connect nordic nrf52832 dk as a central to my custom peripheral(sensor tile) .peripheral is advertising different services and uuid of the one of service is...
Hi,
I want to define two different channel for I2C and interface two slave devices. nRF52840 will always be master in this case. As mentioned in the Product Spec. of nRF52840...
Hi,
I have a 128bit UUID on the ad block which I need to change on the fly to another 128bit UUID.
I tried different solutions and searched for a good example, however...
I want my device to blink a LED periodically when there's a BLE connection. This BLE connection will usually be idle and every now and then there'll be heavy traffic back...
I'm working on a project & I followed the procedure found here
in the answer, it works with me when I tested it when pairing from the bluetooth devices shown, when I tested...
Hi,
I am using nrf42840 dk board,sdk 14.2 and keil IDE.I have integrated bmp180 sensor code with ble_app_proximity code.I have no errors.After loading the code,I am getting...
Hello! I am migrating ble_mpu_simple code from sdk 14.2 to sdk 15.2.While migrating,I am getting the error.
error: #20: identifier "SPIM_CSNPOL_CSNPOL_LOW" is undefined...
Hi team,
I am using nrf52840 Development Kit,sdk 15.2,Keil IDE
I am using MPU6050 sensor.For that,I used nrf5_MPU_examples_master file.
I have integrated ble_mpu_sensor...
Hi,
i was looking for nrfjprog command line tool on nordic website. But this tool not available to download. Is this tool got replaced?
If yes, then which is replaced...
Everybody is good !
I want to know whether BLE can broadcast, connect and communicate normally when nrf52832 communicates with nrf24L01.
The data manual says that it supports...
Hi,
After long time again started working on nordic controller's. Previously my pc was properly configured for NRF5x environment which includes gcc and flahser.
Recently...
The pin connected to lis2dh12's int pin consumes about 300 uA.
But the pin I used as button,also enabled int function , works good.
The pin I used as wake-up is in input...
In order to establish a wireless connection from my pca10056 developing card and a second nRF52840 SoC module using example CLI commands, and then being able to check/set...
Hi,
I have few queries regarding the internal regulators of nRF52840.
1) Is it mandatory to configure the internal LDO or DC/DC regulators of nRF52840 ?
2) If these...
