Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I suffer from the phenomenon which can't sometimes maintain communication between the 32.8ms at Gazell communication at present.
When not writing in SoftDevice, this...
Hi,
I am using " BLE-Gateway " example from nRF51-ble-bcast-mesh to advertise my custom "Manufacturer Data" from 1 nRF51422 device to another nRF51422.
I've made the...
I have been able to implement the PER test (on nRF51822) using the direct_test_mode_s110 and code based off the example python code from the nAN34 zip file. I adjusted to...
Hi,
I want write a demon running on linux to control the 51822 dongle to connect or disconnect with mobile phones.
Now I have one idea, which is using string as command...
Hello,
I need to send packets that are larger than 20 bytes to once characteristic with a variable length. When I set the variable length to 100 bytes, the Attribute table...
NRF51822 supply voltage is 3V battery. When I design principle diagram, I have a question.
Both AVDD and VCC_nRF are connect with the battery's positive?
While trying to get the SDK's bootloader working with gcc, I have to replace some ARMCC-speific code found in bootloader_util_arm.c:
__asm void StartApplication(uint32_t...
I am using the nRF51-DK and have Timer1 setup as follows:
void start_timer(void)
{
NRF_TIMER1->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1...
Hi Guys,
I am currently using the ble driver for windows (Python) to get notifications from two Gatt services (Same Service/charac/descriptors/etc basically same application...
I've just trying to get SPI working, everything is compiling OK but when initialising the SPI, when the line below is hit,
/* Clear waiting interrupts and events */
p_spi_instance...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
I would like to support app_button, however I need to configure a pin as NOPULL and trigger on a low to high transition without debouncing.
I don't see a way this can co...
HI,
We survey APPLE's ANCS right now! But we have a question that need your help.
I use ios device ios 8.3,ble softdevice 8.0
I have some questions about the pairing...
