Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
is there any example using the IEEE 802.15.4 driver?
I was able to send and receive a some packets by using nrf_802154_receive and nrf_802154_transmit_raw, and...
Hi,
i am playing around with configuration of Softdevice (S112 ) + bootloader + application.
Bootloader is custom, really simple. Flashing block of data received via uart...
Hello, I wanted to understand what is the default storage place in the internal flash memory region of persistent info for OpenThread. In the previous SDK (Thread and Zigbee...
Hello DevZone,
I have 2 Thingy91X (not Thingy91), with nRF9161 and nPM1300 inside. These two devices run out of battery for several hours.
The problem is that I can't...
Hi，I have some problems using the NFC routines in the SDK.
The hardware used is nRF5340 DK.
Software is nRF Connect SDK v2.6.99-cs1.
The downloaded and run routines...
Hi,
We have designed a custom board for npm1300 and nrf52832(MS50SFA2 module). We would like to drive the VCC of the BLE module using buck2 but we are only getting 1.8V...
Hi,
I have to use Nordic SDK and VS Code Dev Kit on my company enterprise PC but I cannot fetch the toolchain or install SDKs via VSCode or nRF Connect for Desktop
...
Hi everyone,
I'm the author of the following question and a lot of context information about the state of our custom application can be gathered from there: registration...
Hi,
In my app I have been using the following to register my state change callback. This works. Only issue is it seem to only pass ot_instance, I cant pass a user data to...
Hello All,
I am attempting to use the scanning module to scan with a multiple filters. UUID and NAME filters to be exact.
I have done some testing with the code below...
We are seeing different behavior/performance on our system depending on whether we reset the system using JTAG (JLinkRTT Viewer) or we power cycle the system.
Our project...
Hi,
we would like to extend the measurement range of the PPK2 beyond 0.6 A in source meter mode, e.g. to measure the power usage of a Raspberry Pi. We know that this might...
I need a checksum to verify integrity of some data blocsk. As I saw, that the nrf5340 hardware has some builtin support for SHA-256, I though: cool, let's use SHA-256
Now...
Hi,
I build a custom board (nRF52840) but I'm not able to flash it using nRF5340DK with J-Flash via SWD interface.
1. The first thing I did was to do a full chip erase...
