What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
We have started using nPM1300, but now we are unsure how to proceed.
Through our inquiries, we have learned that development requires the use of the ncs platform. However...
I have an nRF5340 that I'm trying to use a Segger Base Compact debugger with. I can flash and run the application fine. If I try to debug (using the VS Code nRF Connect extension...
Hello,
On the nRF9151 can you force usage of PC5/20dBm powerclass (as opposed to PC3/23dBm) ?
Apparently the %POWERCLASS command is read-only, PC5 cannot be manually forced...
Greetings,
One question on the nRF9161/51 capabilities: How many LTE-M DL HARQ processes are supported ?
I understand that 10 HARQ processes in DL (Rel14) is not supported...
Greetings,
LTE-M Data Inactivity Timer feature (Rel-14 ; Cf. TS36.321 §5.17 Data inactivity monitoring ; dataInactMon-r14 Info Element sent by UE) is normally supported...
Hello,
NB-IoT Dual HARQ and Max TBS size enhancement brought in Rel14 (Cat-NB2): on nRF9160 it was controllable via AT%REL14FEAT, using parameters <NB_dual_harq_support...
Hello,
One question on the Reduced Mobility feature (3GPP Relaxed Monitoring TS36.304 and Nordic-proprietary feature) based on %REDMOB command.
AT manual says :
%REDMOB...
AS-RAI (RAI over Access Stratum ; Rel-14) over LTE-M was available on the nRF9160 via the command AT%REL14FEAT (option <as_rai_support> e.g. AT%REL14FEAT=0,0,0,1,0 to enable...
With the current version of nRF Connect for Desktop I received an error when updating the Toolchain Manager.
I then uninstalled the Toolchain Manager and tried to reinstall...
Hello,
Although my board is not equipped with an external LC filter, I flashed firmware which enables DCDC and this made the chip unresponsive.
Is there any method...
Hey
I'm trying to figure out what is the intetned way of using the tools for configuring a project.
We have the following config files in the following structure:
...
Hello I currently have an error when flashing with j-link on a custom board. The mcu is nRF52833 QDAA and the debugger pin is connected to 4 pins. In VSCODE, CONNECTD DEVICES...
I am working on a pdm microphone INMP621. I am getting the pdm data using nrfx pdm drivers but not sure about the logic which I am implementing to convert pdm to pcm. I read...
Hi, I need a little help with mcuboot.
We want to transfer firmware updates via CAN (MCP2515), which is already implemented. Was we are short of time, and we want to integrate...
