Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Looks like Gazell can't run on nrf52810 with nrf5 SDK :
I don't knnow whether it is possible to create app on it with nrf connect SDK.
I think nrf connect SDK will need...
Hi, I have purchase a circuitdojo_feather_nrf9151 board it has LIS2DH12 and npm1300 on i2c2 i also want to connect SHT40 but facing issue this sensor is not detecting on i2c...
Hey all, I wanted to enable shutdown and standby modes for this chip, but realised that I can not use the layer of zephyr. When i try to CONFIG_PM=y in prj.conf it does not...
Hi,
I'm running the system_off/ sample on v3.2.3 with these settings in prj.conf
And with this overlay file:
However, I can see that there's a high (and in fact...
Hello, I'm building a multi-image project for an nRF9151: a two-stage bootloader (NSIB + MCUboot) plus two independent non-secure app images.
Each app needs to be able to...
I'm using the MCUmgr + MCUboot solution for BLE OTA FW updates (i.e. CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU).
Is there any way to require pairing for firmware updates? I see...
I'm trying to capture a ble connection with nrfutil. What I've done:
- installed nrfutil on my arch based linux machine
- install ble-sniffer
- setup the nRF52840 Dongle...
I am aware from this post https://devzone.nordicsemi.com/f/nordic-q-a/106424/ble-audio-test-app-supporting-both-cis-and-bis t hat the primary LE Audio controller does not...
Hello, I have a wierd bug on my board using an nrf54l10. I am using the sys_poweroff(), function to put my device to sleep. Everything is working fine. However, sometimes...
nRF PPK2 HW is not working with latest 64 bit OS, ARM based processor, the same HW is working on linux/windows(intel based) below is the log from an ARM based processor: ...
Hi all,
I am having problems setting up a proper project running the application core and the flpr for nrf54l15. I want to build the FLPR binaries as completely separated...
Hi everyone,
I have a problem with flashing code to Nora-B126, when i press flash in Visual Studio Code everything works fine. I got:
Parsing image file. Verifying programming...
Currently, I am working on nRF5340 Audio DK boards. I am using two nRF5340 Audio DK boards to function as a walkie-talkie using the onboard microphones. Using the nRF5340...
