Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I'm using a Azure IoT Hub to connect some devices to the cloud and then uses the Direct Method to send messages to the devices. I can send messages and receive the response...
We are using nPM1100 along with a STM CPU. When we put the CPU into deep sleep, it takes one minute for the current to go down to 20uA from 500uA.
We were expecting the...
I have a customised bootloader using uart + BL, built from the SDK examples and modified using articles found here. It works - most of the time. The product is a cusom board...
Hi to all,
this is my first public ticket ;)
I would power a nRF52840 on my custom board both with a cell battery (specifically CR2032) and the VBUS provided by the USB...
Hi, 1. After executing nrfjprog --recover command with PCA10040 DK, I read this hex: nRF52832.hex with Programmer
2. What does this program do that causes read protection...
I have successfully implemented an interrupt-driven method to read data from the MPU6050 sensor on the NRF52840, and it functions as expected. However, I encounter an issue...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
Is there a solution from Nordic available where I can have a LTE-M (or NB-IoT) and at the same time still receive the 1PPS output from the GPS module? It seems to be that...
Hi,
I am working with nrf5340 chip and I want to migrate from NCS 2.6.1 to NCS 2.7.0. I want therefore to apply recommendations: migrate to sysbuild.
With NCS 2.6.1 I...
I have an array of LEDs on my custom board. One of the LEDs is set on a UART0 RTS pin, which is GPIO(0,5), and we are using ground as common. To avoid any conflicts, I disabled...
My device is an nRF52840 running a C Code application that is built on nRF5_SDK_17.1.0 I am implementing a FOTA solution where a hex file fw image and a .dat file will be...
I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...
I'm using a thingy53 on ncs v2.7.0. I turned on CONFIG_ASSERT to try and find issues. This issue pops up randomly, it asserts the program crashes and causes me to have to...
Hello,
I am experiencing difficulties connecting my NRF52840 board to the nRF Connect software. Despite multiple attempts, the board does not appear to be recognized by...
Hi, I'm looking for the public mac address for nrf52840, and i find out that the mac address is located inside the register FICR->DEVICEADDR[0] and DEVICEADDR[1].
DEVICEADDR...