Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello all,
I'm currently evaluating Bluetooth Mesh as potentiell solution for a remote control system with the option to extend the range via range extenders.
To get an...
Hello,
we need to SPI interface of a display controller RM6909 (AMOLED for smart watch) with the NRF52832 processor.
Could you please share us the source code for that...
Hi,
We are currently evaluating the Tracker V2 application.
We would like to increase GPS accuracy, before the nrf9160 returns status GNSS_EVT_DATA_READY. No problem...
hi nordic team，
i have use nrf52840 develop a product ,now i need make sig authentication to sale it .the sdk version i use is 16.0. i m sure it can pass the ble5.0 authentication...
Hey ,
Is there a way to connect and send commands directly using the dongle to the NRF52832?
If so , where can I find a protocol for the communication ?
Hi,
I am testing the sample "machine learning" (from the template nrf/applications/machine_learning) on Thing52. And connect the Thingy52 to the central_uart on nrf52DK_52832...
Hi, in my project I'm using fstorage library to store some information that should be kept even after the firmware update.
For this we are reserving the memory address as...
Hi,
At work we are developing custom HW with an nRF9160, using NCS 1.8.0 for now, but I have confirmed the following behaviour on a nRF9160 DK with NCS 1.9.1 as well.
...
Hi,
after connecting to our mqtt broker I set nrf9160DK to data mode and publish data to our mqtt broker:
After this LTE link monitor is not accepting any AT commands...
Hi,
I am trying to enable extended adverts, when the call to bt_le_ext_adv_create is made, it always returns:
Using the following code:
My custom service has the...
Hello,
I have three devices that use UART, connected to an nRF52832 that I'm using NCS 1.6.0 to program. Since the nRF52832 only has one UART module and Zephyr has no native...
Hi, when following the tutorial, https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial i ran into problems...
hi, I want to use 52832 Comparator function, SDK only has "low power comparator" demo code. Setting reference voltage in MCU, just compare one GPIO with this voltage.
But...
Hi
I was creating a function to send i2c data trough sensor that I use. But when I double check the communication, there is a part that doesn't works properly. So as you...
Hi, Is it possible to enable and Different log level from Zephyr cli using Zephyr Logging API? i am using
LOG_MODULE_REGISTER (AWS, 3 );
I want to change or register...
