Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Follow up on: github.com/.../50438
Describe the bug There is a specific case in which the Bluetooth stack seems to become stuck in a state where it will not accept/initiate...
Hi, We are using SDK17 and are implementing the UART y APP_UART_FIFO_INIT. Every now and then we encounter APP_UART_COMMUNICATION_ERROR. I know this is related to buffer overrun...
Hii team,
today i install wireshark version 4.0 and python 3.10 and i downloded nrf sniffer ble software from nordic website and i connected my nrf sdk to pc to flash code...
Hello,
I'm developing an application that will include over the air updates. I read the infocenter information about how the dfu works, with either dual-bank or single-bank...
Hi,
As I am using the nRF52840 DK for a project, so I followed the instructions for setting up nRF Connect SDK as it's the main SDK going forward: nRF Connect SDK and nRF5...
Hi, How can I get the RLOC16 or similar ID from the CoAP clients connected to my CoAP server? I need to get this information from the messages that the clients send.
Cheers...
My BLE application needs to communicate with another µC using serial UART - so I started my app based on the sample in bluetooth/peripheral_Uart I'm have a nRF52_DK board...
Hello I have flash memory via SPI on the custom board. It works on SDK v2.0.2 properly and doesn't works on SDK v2.1.0. Flash memory defined in Device Tree as mentioned below...
Dear Sir.
we are porting some projects from nRF5 to Zephyr and the UUID/handlers table consume more memory. What is the best practice? we are trying to do the same things...
Hi Nordic community,
Let me ask a question.
I can run AT+RUNIMPULSE command via UART cable successfully, but I cant write it using BLE. For example using Nordic nRF connect...
Hi,
I have tried setting a custom network name by adding
CONFIG_OPENTHREAD_NETWORK_NAME = "MILIEU_OTNET" to prj.conf of both coap client and coap server. But they always...
Hello everyone,
I am trying to use the S340 softdevice in order to connect to an ANT+ HR. I would like to use proximity search.
It works fine for the first device in range...
HI
After the connection between the light-bulb and the Zigbee-Coordinator is completed, it is observed from Sniffer that both parties will broadcast regularly (as shown...
Hello,
I'm writing my own UARTE library because I need some functionality not offered in the SDK. But I came across a hardware behaviour I can't explain.
In my understanding...
