Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Good day
I have been testing sample code code, but when compiling I get this error
nRF5_SDK_17.1.0_ddde560\components\libraries\uart\retarget.c:101:23: error: unknown...
I am plugging the nrf52840 Dongle to the USB port, the computer beeps as it recognizes a new USB device, but when I open the Programmer app from the NRF desktop connector...
Hi,
I am a very beginner in Python and BLE. I would like to use a nRF52840 Dongle to connect to a Bluetooth Device, send 6-Bytes data in the 1401 section and also perform...
Hi All,
i have been working on two i2c devices
1. MPR121, which has slave address (0x5A)
2. PCF8583, its address is (0xA0).
I am using Zephyr I2c api for the same...
Hi,
I would like to ask on where can I find or set the advertising duration or on how long the advertisement would last?
I am using zephyr, nrf52840DK. I want to be able...
Hello,
So, as per the requirement for my project I need to program the Thing:53 using Visual Studio code programmer following the instruction as provided in the below link...
Hi,
Is it possible to perform a HW reset of modem core inside nrf9160 device? If yes, how is this HW reset requested?
Thank you very much...
Regards,
Emerson ...
proj.conf:
nrf52840dk_nrf52840.overlay:
code:
Pretty straightforward. I've looked through the nRF52840 Product Specification and there is no mention of data bits...
From zephyr/samples/sensor/lsm6dso, I found the following code using sensor_channel_get(). API from sensor.h.
}
However, there are more driver API in zephyr/drivers...
Hello I don't see any change in RSSI with different TX power values under Zephyr. 1.9.1
It used to work with Nordic SDK 3.2.0 (see table below) The HCI API in Zephyr that...
On nRF5340, we are using Thread communication, Wifi and LTE-M module.
User can change the interface board, between Wifi or LTE-M module on the same UART bus.
& uart0...
I changed the central UART example to work with a demo I'm writing. I removed the hardware UART part and only send messages to a peripheral. What I do is I measure different...
I'm using an nRF52840 and SDKv17.1.
I have an active-high interrupt source connected to a GPIO pin. I understand that a GPIO should be able to wake up a system from system...
I think the nRF Connect toolchain is missing the right driver for the CLI app on the USB dongle, or the CLI is not setting up the USB interface with the right VIN.
When...
Hi,
Trying to run one of the Acconneer samples I get the errors below:
service_handle = acc_service_create(envelope_configuration); returns a NULL handle, all up to this...
