My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi,
It seems like my system is crushing before going to deep sleep,
I have noticed that if I remove a k_sleep of 500 ms, just before going to deep sleep the system does...
It's successful when I use west :
% west flash -d build
But it's failed when I use nrfjprog :
% nrfjprog --program merged.hex --reset
OR
% nrfjprog -f unknown...
Hi nordic:
I use two NRF52DKs and download MESH CHAT separately, hoping to achieve communication between the two NRF52DKs:
SOFT VER: NCS2.8
The specific process is as...
Now I have a verification work on the nrf52840 development board, which is to verify whether the terminal device will perform signature verification after receiving OTA firmware...
I just freshly (Nov 25, 2024) installed the nrfutil 'core' exe and the nrfutil device command.
I try to list my nrf devices (a nrf52840 dongle is connected and another nrf52840...
I have some of these boards which come already flashed with the AdaFruit CDC/DFU/UF2 bootloader , allowing them to be programmed without a dedicated programmer. I wanted to...
I have noticed that the project name used for sysbuild is the same as the folder name where my code is checked out. So if I have the application in a folder named "src" the...
Hi,
I had a problem while programming my custom nRF52832 board using nRF52840DK. I am using this connection that I found in the Nordic Devzone forum. I am trying to program...
I'm developing my project by nrf5 SDK in nrf52832.
Pairing and bonding used in my project and implemented by peer_manager.The pm_evt_handler() defined as follow:
Due...
Hello everyone,
I was looking at SPAKE2+ example (NCS v2.6.99) and trying to understand where the password used to derived the shared secret is set or used. Can anyone help...
Hello,
I'm trying to move my project based on the xiao_ble board from using SDK 2.6.2 with Adafruit_bootloader to SDK 2.9.0 with MCUBoot/sysbuild.
To keep things simple...
nRF5_SDK_17.1.0
PCA10059
For I want to provide up to 20 central connections, I have defined the objects like this( inherited from example code):
The conn_handle is...
I have built my own firmware for my nrf54l15 custom board and got a merged.hex file.
Now I want to flash this firmware(merged.hex) to my nrf54l15 custom board on another...
Hi,
I have updated and old old project to SDK 17.0.1 and using Segger Embedded Studio
But because I make a lot of use of pstorage in the project - I am not ready to convert...
Our product is experiencing an issue where a watchdog reset occurs after DFU, even though we are feeding the watchdog in the application.
However, this issue does not occur...
