Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello
I am using the NRF9160 and I can see that modem RF transmitions cause some EMI issues
I would like, for a period of few seconds each time to stop modem transmitions...
Hi, dear Nordic team,
We've already purchased a few thousands of BC805M BLE modules (nRF52805) for our upcoming mass production. During R&D, according to datasheet, we...
I need to use Delay of few Micro/ Milli / Seconds without pushing the MCU in sleep i.e. without using k_msleep() etc. Is there any library for this purpose in Zephyr ?
Hi, Hope you can help. With a nrf52840dk development kit arriving tomorrow. We tried to make a start with a nRF52840 dongle, which we eventually want to use. Connected to...
Hello,
I follow the doc to install the nrf_sniffer_for_bluetooth_le_4.1.0
- Flashing the nRF52840 dongle with nRF Connect for Desktop
Uploading image through SDFU: 97...
Hi,
I'm trying to use a nRF52840DK as a zigbee router implementing a temperature sensor. The setup is composed of
Software
Application: Home Assistant
SDK: nRF5...
Hi, I'm trying to achieve high throughput of BLE on connection between two nRF52840 DK.
I've read some articles about it, and configured both Central and Peripheral devices...
Hi,
I'm looking at the nrf5340 PS v1.2, page 75 & 76 regarding the audio clock PLL. Using the formulae given, I'm finding that the register value that yields the closest...
Very much a beginner at this so if this is inappropriate for this forum do not hesitate to let me know.
Starting out trying to develop a BT Mesh system. I purchased a nrf53...
Hallo Dears,
I would like to develop a ble-peripheral role device with a humidity sensor service. I found the development kits from the nRF5x family such nRF51, nRF52...
Hi,
I'm trying to take advantage of nRF52840 as Zigbee NCP in communicate with a host microcontroller via UART. My problem is I don't know what I have to send and what will...
Hi,
In your LE audio presentation from CES that you had a demonstration of a low latency setup with LE audio. We are more curious about the setup you demonstrated so we...
I have built and successfully run this application with the nRF Cloud and then I achieved a partial success with running this application with the AWS IoT.
When I run this...
Hi there, My nRF52840 Dongle suddenly stopped working. The application that used to work among a few last weeks stopped during one of exploatation. Pressing Reset Button don...
