Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I’m trying to clarify the maximum ADC input voltage specification for the nRF54L15. Am I correct in assuming that it’s limited to the maximum IO voltage, i.e. VDD...
Hello,
I have developed a BLE Peripheral application on the nRF52840 (SDK 17.1.0) which works correctly. Later, I tried to integrate/port an SPI peripheral example into...
Hi,
I am a bit stuck with configuring nrf5340 project to include the bootloader properly.
The SDK-toolchain I use is v3.0.2
What I need:
encrypted and signed update...
Hello,
We are trying to increase the upload speed of our BMD-350 module. Right now we are averaging about 3kB/s according to nRFConnect.
See attached image of upload...
Hi No rdic support tea m, I'm developing a custo m appl ication on t he Thingy53 and have encountered challen ges implementing two key features that a ren't cov ered in the...
Hi all,
I'm trying to set up MCUMGR on 54L15, such that it can receive images from my border router when they're in the same Thread network. I read that we can upload images...
HI
A phenomenon occurs where the current remains at 20mA intermittently.
Actually, the BLE specification states that RF TX/RX is less than 10mA....
I'd like to know...
We are in the process of porting from nRF SDK v15.3.0 to v17.1.0.
After updating, we’ve noticed that the device sometimes gets stuck. Investigation shows this is related...
I have a custom board using a nrf5340 and a st7789 display using spi and mipi_dbi. It's I have it working on a sample project and printing "Hello World" I was using nrfConnect...
Does this mean that Bluetooth LE Power Control (LEPC) feature is not at all supported by any of the Nordic chipsets? I am particularly curious about nRF54 series with the...
Hello,
Following this link I integrated the extended power save mode in my code,
I put the nrf7002 in extended power save mode after successfully connecting to the AP...
I'll preface this by saying I am new to developing on the nRF and the Zephyr OS.
I am just trying to set up a flash read/write module on my nRF52DK PCA100040 model. From...
I'm using pc-ble driver-master for programming. The hardware uses 52840 dongle and calls SD_API_V5. After I successfully connected, I sent a pairing request using the sd_ble_gap_authenticate...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hello all,
I’ve already looked in the following files:
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr\bluetooth\mesh\ access .h
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr...
