Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I've added usb function to nRF52840 project accroding to usb sample projects.
The function was all right but the device manager showed the the 52840 as "USB serial...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
The timer is called for every...
I have a Fanstel BT832X evaluation board (model EV-BT840(832)-V4). Nordic examples without softdevice are working fine. Examples with softdevice are not working. I have checked...
I’m getting some strange behavior after repurposing the WS2812 driver sample with the following code. Note that my code has Bluetooth enabled. It seems like it might be some...
I use ncs1.6.0 to develop on nRF52832DK. The current requirement is to enable PA LNA support on mesh.
I learned how to use FEM driver through this blog . I added the corresponding...
Hello,
Is it okay to supply the nRF21540 with a DC/DC or do I need to use an LDO? Are there any performance differences of the nRF21540 when choosing one over the other...
I'm finding that the signal strength of the radio is too low in my nRF52840 custom BLE project. I would like to increase the radio power from the default 0dB as our RSSI values...
I made a custom model under ncs1.6.0 to publish uart data. When the data I want to publish exceeds 85 bytes, an error occurs in debug:
<err> bt_conn: Unable to allocate...
NCS v1.6.0
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
When Serial LTE modem is woken up after #XSLEEP=2 without 2s delay, it starts to loose some unsolicited...
Hello,
I'm using the sdk v17.0.2 with softdevice s140 with a custom PCB shipping the nrf52840.
I'm facing an issue where I cannot enable NFC and softdevice at the same...
Hello everybody. I am currently evaluating some BLE Tags, if they can be used as an BLE doorkey. The chips I am talking about are the following: nRF51802 nRF51822 nRF52832...
Hello support team,
I try to get the NRF52840 DK to work as a central with FreeRTOS. Connecting and getting notifications works well, but the device freezes on a disconnect...
I am running a Zephyr OS, and I am using the mbedtls APIs to do my cryptographic operations using the Cryptocell as my backend. My question is should I be using a mutex of...
