Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
We have a physiological monitoring system in production where we used NRF52832 as a peripheral. Connecting this peripheral with Windows bluetooth, we realised that...
Hello,
I'm currently looking at using a last will message that updates an attribute on the cloud if the device disconnects from the broker. The broker and client agrees...
Hello everyone,
My current setup:
1.Development Kits = NRF52840
2.Nrfutil Version = 6.0.1
3.Softdevice = S140
4. Operating System = Linux
In current goal is to...
Hi There,
I am currently using a custom bootloader for my devices which was started from the secure bootloader example given in the SDK, I am using BLE as the transport...
i have nRF Connect SDK v1.6.1，excuted “west update” and “west zephyr-export” command（the project will not built successfully without executing these 2 commands）
then i was...
ncs version 1.6
SES
Windows 10
I have installed ncs completely using standard tools.
Now I am following the tutorial Part 1.
The project hello_world is created...
Hi,
I have a GPIO used as input or output. When it's used as an input (99% of the time), I have an interruption on it (falling and rising edge).
When I use it as a output...
This is my first time using Nordic SoCs, so forgive me if this is a silly question. I have a Fanstel BT832X evaluation board (model EV-BT840(832)-V4). I tried the Nordic's...
I upgraded the code from sdk13 to sdk17.
The setting is the same as the original code and there is no error.
However, if I build, the original code is built with the app...
how am i going to merge ble_app_multirole_lesc and ble_app_blinky
I add
into ble_app_multirole_lesc main.c
and it stuck in services_init()
seems like the err_code...
Hi,
I would like to make a system that goes to sleep for a while and wakes up for a short time thanks to the rtc. According to the documentation, the power consumption of...
Excuse me：
PPK2 doesn‘t work，I don't know why，The computer does not recognize the usb port after connecting the USB cable，The indicator light of ppk2 is not on.What should...
Setup:
nRF PPK2 is connected via USB to the port DATA/POWER to the PC
Running nRF connect version 3.7 from ubuntu 20 causing the following issue, when using "Power Profiler...
Hi, I'm having issues programming my Thingy91 via the NRFConnect programmer app.
The Thingy in question has had various applications run on it over time, but the objective...
Hi,
I am currently setting up an MQTT client via the MQTT publisher sample on zephyr.
My mqtt client is a NRF5340 and it is connected via ethernet with my pc and also...
